TFT Displays for Test and Measurement Instruments: Resolution, Viewing Angle and Noise
A display on a test or measurement instrument has one job that most screens do not: it must not get in the way of the measurement. That means enough pixels to show a waveform without stepping, a viewing angle that works on a bench or in a rack, a backlight that does not inject noise into the front end, and a part that is still available when the instrument is in its eighth year of production. This page covers those points and the TFT references that fit handheld meters, portable analyzers and bench instruments. If your instrument only shows digits and a few icons, a segment LCD may still be the better choice; see measuring instrument LCDs. We supply OEM projects from 1,000 pieces.
Request a quote WhatsApp +86 134 3360 8240 TFT LCD catalogue
Which display fits which instrument
| Instrument | Display that fits | Catalogue references |
|---|---|---|
| Handheld meter, clamp meter or tester with a graphic screen | 3.5 in TFT; transflective for field use on battery | S350FPQI (240 × 320, SPI + RGB, transflective), S35001D (320 × 240, RGB, 850 cd/m² typical, anti-glare, −20 to +70 °C) |
| Portable analyzer or handheld scope | 3.5 to 5 in with more pixels for traces | S350FLVH-01 (3.5 in, 480 × 640, RGB + SPI, transflective), STFT50-01D (5 in, 800 × 480, MIPI + RGB, capacitive), S500MIWI-04 (5 in, 800 × 480, RGB) |
| Bench instrument, power supply or source meter | 7 in, RGB or LVDS | S700MIWN-18-W (800 × 480, RGB), S700MB1XH-09 (1024 × 600, LVDS) |
| Large bench instrument, test station or ATE front panel | 10.1 to 15.6 in, LVDS or eDP | S10MB1XH-07C0 (10.1 in, 1024 × 600, LVDS, capacitive), S10MHYH-02 (12.1 in, 1280 × 800, LVDS), S60MZJW-01 (15.6 in, 1920 × 1080, eDP) |
How many pixels a waveform needs
Resolution on an instrument is about how finely a trace can be drawn, not about how sharp the menus look. Take a plot area with the usual 10 horizontal and 8 vertical divisions:
Worked example. On an 800 × 480 panel, leaving room for menus and readouts, the plot area might be 700 × 400 pixels. That gives 70 pixels per horizontal division and 50 per vertical division. On a 1024 × 600 panel with a 900 × 500 plot area, it is 90 by 62.5. On 1280 × 800 with 1100 × 700, it is 110 by 87.5. A detail smaller than one pixel step, 1/50 of a division in the first case, simply disappears unless the user zooms. If your instrument’s selling point is resolving small signals on screen, the vertical pixel count of the plot area is the figure to compare.
Our screen size and PPI calculator gives pixel pitch and density for any size, and the pixel clock calculator checks whether your processor can drive the panel at the frame rate you need for live traces.
Viewing angle on a bench and in a rack
A bench instrument is read from above, from the side, and by two people at once. A rack-mounted unit is often read from well below or above its centre line. Twisted nematic panels shift contrast and colour quickly off axis, so colour-coded traces can become hard to tell apart. IPS-type panels hold colour and contrast over a much wider angle and are the safer choice for instruments. See IPS TFT display modules and TN vs IPS.
Keeping the display out of the measurement
The display is a noise source inside the instrument. Three places to look:
- Backlight dimming. PWM dimming switches the LED current on and off, typically at a few hundred hertz to tens of kilohertz. If that frequency or its harmonics fall in your measurement band, move it, filter the LED supply, or ask for an analog (DC) dimming input. Dimming options are covered on high brightness TFT modules.
- Display link. LVDS is differential and quieter than a wide parallel RGB bus, but its clock still radiates if the cable and ground are poor. Spread-spectrum clocking and a short, shielded cable help. Our LVDS EMI and signal integrity guide has layout numbers.
- Ground and ESD. Return the display and backlight current to the supply, not through the analog ground, and protect the touch panel and FPC from ESD at the front panel. See the LCD ESD protection guide.
Field instruments: battery and daylight
Handheld instruments spend the day outdoors on a battery. A transflective panel reads better in bright light while keeping the backlight low, and a segment or memory LCD uses less still if the screen content allows it. The trade-offs, with a battery-life calculation, are in low power display options compared. For cold and hot field use, check wide temperature TFT modules.
Instrument lifecycles are long
Instruments often stay in production for seven to ten years, and a display change can force a front panel or firmware update. Put written change notices and a last-time-buy window into the supply agreement, and keep a second reference with the same outline in mind. Our page on component obsolescence in TFT displays explains what usually goes end of life first.
Quantities and what to send
We work on OEM terms: production orders start at 1,000 pieces, and evaluation samples are arranged per project. The group factory that builds our modules holds IATF 16949, ISO 9001 and ISO 14001 certificates. To quote an instrument display, send the instrument type, size and resolution, the host interface, whether it is used on a bench, in a rack or in the field, any noise-sensitive frequency bands, and the expected yearly volume.
Test and measurement display FAQs
What resolution does a measurement instrument display need?
Work from the plot area. With 10 by 8 divisions, an 800 × 480 panel gives about 70 by 50 pixels per division, and a 1280 × 800 panel about 110 by 87. Pick the panel whose vertical pixel count resolves the smallest detail users need to see.
Should an instrument use an IPS or a TN display?
IPS is the safer choice for bench and rack instruments, because contrast and colour hold over a wide viewing angle and colour-coded traces stay distinguishable off axis.
Can the display backlight affect measurements?
Yes. PWM dimming and the display link can couple noise into a sensitive front end. Moving the PWM frequency out of the measurement band, using analog dimming, and routing display current away from the analog ground reduce it.
What is the minimum order for an instrument display?
Production orders start at 1,000 pieces. Evaluation samples are arranged per project before an order is placed.
Designing a test or measurement instrument? Send the instrument type, display size, interface and where it is used, and we will suggest a panel and front stack. Ask about an instrument display.
