Low Power Display Options: Segment LCD, Memory LCD, E-Paper, OLED and TFT Compared
For a low power display that shows live data, a reflective segment LCD is the floor: the glass and its driver together draw a few microamps, which a coin cell can supply for years. A memory LCD adds a pixel matrix for roughly 12 to 50 µW, and e-paper holds a static image with no power at all but spends energy on every update. OLED and TFT modules are set mostly by lit pixels or by the backlight. Which one fits depends on how often the content changes and whether it must be read in the dark.
Request a quote WhatsApp +86 134 3360 8240 Monochrome LCD catalogue
Where a display’s power goes
A display has four consumers: the light source, the panel drive, the controller, and the work the host does to refresh it. In a transmissive TFT the LED backlight dominates. A reflective display has no light source, so only the panel drive is left. A bistable display removes even that between updates. This is why the choice of technology moves the power budget by orders of magnitude.
| Technology | Power with a static image | Cost of an update | Read in the dark | Typical content |
|---|---|---|---|---|
| Reflective segment LCD | About 5.6 µA at 3.3 V for driver plus glass (NXP PCF8553 typical values, 160 segments) | None extra | Needs a backlight and a transflective polarizer | Digits, icons, bar graphs |
| Memory LCD | 12 µW typical, 50 µW with a 1 Hz update (Sharp LS013B7DH03, 1.28 in, 128 × 128) | Small | Needs its own light | Monochrome graphics and text |
| E-paper (bistable) | None | Energy for every refresh | Needs a front light | Pages that change rarely |
| OLED | Follows the lit pixels. A dark pixel draws nothing | None extra | Emits light | Sparse bright graphics on black |
| Transmissive TFT | Set by the LED backlight | None extra | Backlit | Colour graphics, video |
| Transflective TFT | Panel and logic only when the backlight is off in daylight | None extra | Backlight on demand | Colour graphics outdoors |
Worked example: display life on a CR2032. Assume a 220 mAh coin cell and count the display only, ignoring the microcontroller and self-discharge. Segment LCD: 0.6 µA for the driver plus 5.0 µA of LCD current into a 1.6 nF glass load is 5.6 µA, and 220 mAh ÷ 0.0056 mA ≈ 39,300 hours, about 4.5 years. Memory LCD updating once a second: 50 µW ÷ 3 V ≈ 16.7 µA, and 220 ÷ 0.0167 ≈ 13,200 hours, about 1.5 years. A small TFT whose backlight runs 3 LEDs in series at 20 mA, assuming 3.2 V each, takes 192 mW. A coin cell cannot deliver that. From a 2,000 mAh, 3.7 V lithium cell (7.4 Wh) the backlight alone lasts about 38 hours.
Low power LCD display: reflective segment glass
A segment LCD is a capacitive load driven with a low-frequency AC waveform. Nothing emits light, so the drive current is the whole budget. The PCF8553 figures above are for a frame frequency of 64 Hz. The same driver can be set to 32, 96 or 128 Hz, and current rises with frame frequency, glass capacitance and drive voltage.
Two drawing choices matter most: a reflective rear polarizer, and the lowest operating voltage that still gives the contrast you need. These catalogue references all use a reflective rear polarizer with 1/4 duty, 1/3 bias and a 64 Hz frame frequency.
| Reference | Display mode | Operating voltage | Operating temperature | Connection |
|---|---|---|---|---|
| S3719D | FSTN, positive | 3.0 V | −20 to +70 °C | Pins, 2.00 mm pitch |
| S4745D | FSTN, positive | 2.7 V | 0 to +50 °C | Zebra connector |
| S4608D | HTN, positive | 3.3 V | −10 to +60 °C | 39 pins, 2.00 mm pitch |
| S3629D | TN, positive | 5.0 V | 0 to +50 °C | Zebra connector |
If the product must be read at night, a transflective polarizer with an LED that lights only on a key press keeps the average current low. Duty and bias are explained in segment LCD duty and bias. The limit of segment glass is that the artwork is fixed. A new icon means a new glass design.
Memory LCD: a pixel matrix at microwatt level
A memory LCD has memory in every pixel, so the panel keeps the picture and a still image needs no data refresh from the host. Sharp’s LS013B7DH03 is a typical small part: 1.28 inches, 128 × 128 dots, a 3.0 V supply and a serial interface clocked at 1 MHz. Its datasheet gives 12 µW typical with no update and 50 µW typical with a 1 Hz update, and an operating range of −20 to +70 °C.
The trade-offs are practical. Most parts are monochrome. Sharp describes this one as reflective and only slightly transmissive, with about 0.2 percent transmission, so it relies on ambient light. And these are standard parts: Sharp’s brochure lists sizes from about 1 inch to 4.4 inches, and you choose from that list. For a product with a long service life, read display component obsolescence before designing around a single part number.
E-paper: a bistable display with zero hold power
Electrophoretic e-paper is bistable. It holds text and images without electricity and draws power only when the content changes. Its energy use therefore follows the number of updates, not the hours of operation. A shelf label that changes once a day suits it. A reading that changes every second gives the advantage away and is a case for a segment or memory LCD. The full comparison is in e-paper vs LCD.
OLED and TFT: when the product needs light or colour
An OLED pixel that is off draws no power, so OLED power follows the image. One published comparison puts a mostly black image at around 40 percent of the power of an LCD, and a white background at more than 300 percent. On an OLED, draw the interface as a few bright elements on black.
A TFT spends its power in the backlight, so the savings are in how long and how bright it runs: dim with an ambient light sensor, time out quickly, and wake on touch. Where the product is used in daylight, a transflective TFT can stay readable with the backlight off. Our S350FPQI is a 3.5-inch transflective reference, 240 × 320 pixels with SPI + RGB. See transflective LCD displays for how that mode works.
How to choose a low power consumption display
- Fixed digits and icons that update every second, on a coin cell: reflective segment LCD.
- Free monochrome graphics or text, always on, updating up to about once a second: memory LCD.
- A page that changes a few times a day: e-paper.
- Must glow in the dark, with a mostly black screen: OLED.
- Colour, images or a touch interface: TFT, and a transflective one if it runs outdoors on a battery.
When the lowest-power option is the wrong one
Reflective displays need light from somewhere. If the product is read mostly in the dark and the light stays on, the saving over a backlit display shrinks. Temperature also narrows the field. The segment references above run from 0 to +50 °C up to −20 to +70 °C depending on the reference, so match the range to the product, and check it in the datasheet for e-paper as well. Positive TN, HTN and FSTN glass has a preferred viewing direction, 6 o’clock on these references, which matters for a device read from above. See LCD viewing direction.
FAQ
Which display uses the least power?
For a static image, e-paper, because a bistable display holds it with no power. For live data, a reflective segment LCD: driver and glass together draw a few microamps. A memory LCD sits between the two, at about 12 to 50 microwatts for a 1.28-inch panel.
What is a low power LCD display?
Usually a reflective segment LCD with no backlight. The liquid crystal is a capacitive load driven at a low frame frequency, so a 160-segment glass and its driver can run on about 5.6 microamps at 3.3 V, using typical values from the NXP PCF8553 datasheet.
Does a memory LCD need a backlight?
Not in ambient light. Sharp describes its 1.28-inch LS013B7DH03 as reflective and only slightly transmissive, with about 0.2 percent transmission. In the dark it needs its own light source.
How long can a coin cell run a segment LCD?
Counting the display only, a 220 mAh CR2032 supplying 5.6 microamps lasts about 39,000 hours, roughly 4.5 years. The microcontroller, the sensor and self-discharge shorten that, so budget the whole circuit.
Designing a battery-powered product? Send the battery, the target life, what the display must show, how often it changes and the lighting it is read in. We will suggest a segment, monochrome or TFT reference and the polarizer and backlight options that fit the power budget. See custom segment LCD and monochrome LCD products, or ask about a low power display.
