EMI-Resistant LVDS TFT LCD Modules: Signal Integrity and PCB Layout Guidelines

An LVDS TFT LCD module resists EMI when the whole link is balanced: 100 Ω differential pairs matched within about 5 mm, one 100 Ω termination at the receiver, a single return path, and a cable shield grounded at both connectors. LVDS itself is a quiet interface, because each pair carries about 3.5 mA in opposite directions and swings only about 350 mV. Most emissions and field upsets come from what surrounds it: pair skew, impedance breaks at connectors, an unshielded flat cable and the backlight driver. SuccessLCD supplies LVDS TFT modules from 5 to 12.8 inches, for example the S700MB1XH-09 (7 inch, 1024 × 600) and the S10MB1XH-07C0 (10.1 inch, 1024 × 600, capacitive touch).

Request a quote TFT LCD catalogue

How LVDS works on a TFT module

LVDS (low-voltage differential signaling, TIA/EIA-644) sends each bit as a current of about 3.5 mA steered one way or the other through a wire pair. Across the 100 Ω termination that gives about 350 mV, centred near 1.2 V. The two wires carry equal and opposite currents, so their fields largely cancel, and noise that couples equally onto both wires is rejected by the receiver.

Display panels use the FPD-Link arrangement. Each data pair carries 7 bits per pixel clock, next to a separate clock pair. How the colour bits are placed on the pairs is the data mapping, and host and panel must agree on it.

MappingData pairs + clockWiresWhere the colour bits go
jeida-18 (6 bits per colour)3 + 18All 18 colour bits plus sync and DE on pairs 0 to 2
vesa-24 (8 bits per colour)4 + 110The two most significant bits of each colour on pair 3
jeida-24 (8 bits per colour)4 + 110The two least significant bits of each colour on pair 3

With the wrong mapping the picture is stable but the colours are wrong, because the receiver gives the bits the wrong weights. Rule that out before chasing signal integrity. Also check the channel count. OpenLDI specifies a single link up to a 112 MHz pixel clock, and formats above that are split across two channels.

Worked example: bit rate and skew on a 7-inch 1024 × 600 panel. Assume a total frame of 1344 × 635 including blanking at 60 Hz. For a real design take the timing from the panel datasheet. Pixel clock = 1344 × 635 × 60 ≈ 51.2 MHz. Each pair then carries 7 × 51.2 ≈ 358 Mbit/s, so one bit lasts about 2.8 ns. TI asks for pair lengths matched within 5 mm. On FR-4, assuming a dielectric constant near 4.3, a signal covers about 0.145 mm per picosecond, so 5 mm is roughly 35 ps, a little over 1 percent of the bit. The data would survive far more skew. The limit is tight because skew turns part of the differential signal into common-mode current, and common-mode current is what radiates.

Where the EMI in an LVDS display link comes from

  • Imbalance inside a pair. A length mismatch, a via on one trace only, or uneven spacing through a connector converts differential signal into common-mode current.
  • The clock pair. It repeats at the pixel clock, so its harmonics show up as narrow peaks. In the example above they sit at multiples of 51.2 MHz.
  • Fast edges. TI notes that LVDS transitions can be as short as 260 ps, which makes a trace behave as a transmission line within a few centimetres. Stubs and unterminated branches reflect.
  • The cable. An unshielded flat cable is the antenna for whatever common-mode current reaches it.
  • The backlight driver. The LED boost converter and its PWM dimming share the cable and the ground with the LVDS pairs. Scan with the backlight on and off to separate the two sources.

LVDS signal integrity: PCB layout guidelines with numbers

ItemGuidelineSource
Differential impedance100 Ω nominal. Keep every section of the path within 90 to 130 ΩTI SLLA014
Length match within a pairWithin 5 mmTI SLLA014
TerminationOne resistor of 90 to 130 Ω across the pair, 1 to 2 percent tolerance, within 10 mm of the receiver pinsTI DS90LV028A datasheet
StubsShorter than 10 mmTI DS90LV028A datasheet
Pair spacingTightly coupled and constant. Traces 1 mm apart radiate far less than traces 3 mm apartTI DS90LV028A datasheet
Stack-upAt least 4 layers, LVDS over an unbroken ground plane, single-ended logic on another layerTI DS90LV028A datasheet
Bends and vias45 degree bends or arcs, few vias, and the same parasitics on both traces of a pairTI DS90LV028A datasheet, SLLA014

Ask the module supplier where the termination sits. If the receiver on the panel already has its 100 Ω resistor, a second one on your board puts two in parallel, about 50 Ω, and the line is mismatched. To check your pixel clock against the interface, use the pixel clock and bandwidth calculator.

LVDS cable and connector checks

LVDS defines electrical levels, not a connector or a pinout, so check every cable against the panel’s pin assignment and then against these points.

  • Impedance and skew. Each pair should stay within 90 to 130 Ω. TI quotes 40 to 120 ps of skew per metre for good-quality cable.
  • Length. FPD-Link is commonly described as working to about 5 m. Inside a product, keep the cable as short as the mechanics allow, because a shorter cable is a smaller antenna.
  • Shield. Bond the shield at each connector with a short pigtail to a ground close to the connector, and keep one return path between the two boards.
  • Flat cable. FFC is unshielded. Where it passes near an opening in the enclosure, use a shielded FFC or a twisted-pair harness.

EMI controls beyond layout

Spread-spectrum clocking modulates the pixel clock slightly so its energy spreads over a band. The narrow peaks drop, although the total radiated energy does not. Enable it only if the panel datasheet states the modulation it tolerates.

A common-mode choke on each pair near the connector attenuates common-mode current and passes the differential signal. Choose a part specified for the bit rate, since any imbalance inside the choke works against you.

Decide with the supplier how the module’s metal frame connects to chassis ground, and give the backlight driver its own input filter. Exposed connector pins also need ESD protection, covered in the LCD ESD protection guide.

Choosing an LVDS TFT LCD module for industrial equipment

EMC compliance is tested on the finished product. For industrial equipment the usual generic standards are IEC 61000-6-4 for emissions and IEC 61000-6-2 for immunity. A display module has no enclosure, cable or host of its own, so a module cannot be certified as EMI-resistant apart from your system. What the supplier can give you is the information that decides the result:

  • channel count, colour depth and data mapping;
  • pixel clock range, and whether spread-spectrum clocking is tolerated;
  • where the termination is, and the connector pin assignment;
  • cable options: length, shielded FFC or twisted pair, custom FPC;
  • grounding points on the metal frame;
  • whether the LED driver is on the module, and its PWM frequency range.

These are the LVDS references in our catalogue. Connector and pin assignment are confirmed for each project.

ReferenceSizeResolutionOutline (reference)
S500MHWS2-015 in800 × 480120.7 × 75.8 mm
S700MB1XH-097 in1024 × 600164.8 × 99.8 mm
S800MEKH-018 inConfirm for the project192.8 × 116.9 mm
S10MB1XH-07C0, capacitive touch10.1 in1024 × 600235 × 143 mm
S10MHYH-0212.1 in1280 × 800277.7 × 180.6 mm
S80MHJH-04-W12.8 in1920 × 1080294.4 × 175 mm

When LVDS is the wrong interface

If the display sits metres from the host, or the cable flexes through a hinge, a serializer link such as FPD-Link III is a better fit. It embeds the clock in the data on a single pair, which removes clock-to-data skew and the need for length-matched cables. For a microcontroller without an LVDS output, choose an RGB or MIPI panel before adding a bridge chip. See interface options for an OEM TFT module.

FAQ

What is LVDS in an LCD display?

LVDS is low-voltage differential signaling, defined in TIA/EIA-644. In a display it carries the pixel data as currents of about 3.5 mA on 100 ohm differential pairs, with 7 bits per pixel clock on each pair. An 18-bit panel uses 3 data pairs plus a clock pair, and a 24-bit panel uses 4 plus the clock.

How do I reduce EMI from an LVDS TFT display?

Keep every pair at 100 ohm differential and matched within about 5 mm, terminate once at the receiver, and give the link a single return path. Shield the cable and ground the shield at the connectors, then consider spread-spectrum clocking if the panel allows it. Check the backlight driver separately, because it shares the cable and the ground.

Are all LVDS cables the same?

No. LVDS fixes the signal levels, not the connector or the pinout. Cables differ in pair count, pin order, impedance and shielding, so a cable from another panel can fit the socket and still be wrong.

Planning an LVDS display for industrial equipment? Send the host processor or bridge chip, the cable length and route, the colour depth and the EMC standard your product must pass. We will check the mapping, pin assignment and cable options against a suitable reference. See custom TFT displays and the TFT LCD module catalogue, or send an LVDS display enquiry.

Scroll to Top
Get a QuoteWhatsApp