Which Interface Options Should You Require for an OEM TFT Display Module?

Require the interface the panel speaks natively, and choose it from your host processor: SPI or parallel RGB on small panels, MIPI DSI when the processor has DSI lanes, and LVDS or eDP on larger panels. HDMI and USB are not panel interfaces. A module that takes HDMI carries an HDMI to LVDS converter board (or one that outputs RGB or MIPI), and a USB display adds a graphics chip and a host driver. Ask for them only when the host is a PC or single-board computer with no display output you can route to the glass. SuccessLCD supplies TFT modules on all five native interfaces, for example the S550MEKI-01 (5.5 inch, 720 × 1280, MIPI DSI), the S10MB1XH-07C0 (10.1 inch, 1024 × 600, LVDS, capacitive touch) and the S60MZJW-01 (15.6 inch, 1920 × 1080, eDP).

Request a quote TFT LCD catalogue

Native TFT panel interfaces versus HDMI and USB converter pathsA microcontroller drives the TFT panel directly over SPI or parallel RGB, and an application processor over MIPI DSI, LVDS or eDP. A PC or single-board computer with only HDMI needs a converter board with an HDMI receiver and an LVDS transmitter. A PC with only USB needs a USB graphics chip and host driver, whose HDMI or DisplayPort output then goes through the same kind of converter board.Native panel interfaces vs converter boardsGreen: the host drives the panel directly. Amber: an extra board sits in between.MicrocontrollerRGB LCD peripheral or SPIApplication processorMIPI DSI, LVDS or eDP outputPC or SBCHDMI output onlyPCUSB onlyTFT panelnative inputSPI or parallel RGBMIPI DSI, LVDS or eDPConverter boardHDMI receiver + LVDS TxHDMILVDSUSB graphics chipneeds a host driverUSBHDMI or DPEach amber box adds power, configuration work and one more part that must stay in production.
Figure: SPI, RGB, MIPI DSI, LVDS and eDP connect the host straight to the panel; HDMI and USB need extra boards.

Start from the host, not the panel

At a given size there are only one or two panel interfaces on offer, and the host decides which you can use without extra silicon. So the first line of a display RFQ should be the processor part number and its display outputs. Common cases:

  • A microcontroller with an RGB LCD peripheral, such as Espressif’s ESP32-S3, streams pixels from a frame buffer by DMA. Some RGB panels also need SPI commands at start-up.
  • An application processor running Linux or Android may offer MIPI DSI, LVDS, HDMI or several of them; its reference manual says which pins carry what. Raspberry Pi boards, for example, have DSI connectors alongside HDMI; see Raspberry Pi display options.
  • A PC or an x86 box may expose only HDMI or DisplayPort at its connectors. That is where converter boards come in.

If the host has two usable outputs, use the one the panels at your size already have. A bridge can translate almost anything, but it is one more part to qualify, power and keep in production.

Native interfaces by panel size in our catalogue

Interface and size go together. Our TFT references that state an interface fall out like this:

InterfaceSizes in the catalogueResolutionsExample references
SPI1.54 to 1.77 in128 × 160, 240 × 240S177MEHS-04
Parallel RGB1.44 to 7 in128 × 160 to 1024 × 600S430MBWS-01 (4.3 in, 800 × 480), S700MIWN-18-W
RGB with SPI for commands3.5 to 5 in240 × 320 to 480 × 854S500MHZI-01 (5 in, 480 × 854)
MIPI DSI3.97 to 10.1 in480 × 800 to 800 × 1280S550MEKI-01, STFT1010D
LVDS5 to 12.8 in800 × 480 to 1920 × 1080S10MB1XH-07C0 (10.1 in), S80MHJH-04-W (12.8 in)
eDP15.6 in1920 × 1080S60MZJW-01
HDMI or USBNone as a native inputAny, through a converterConverter board plus one of the above

Parallel RGB stops at 7 inches. A 24-bit bus with clock, sync and data-enable lines is 28 signals, and larger panels move to differential links that carry the data on fewer wires. Nothing in the list accepts HDMI or USB directly.

eDP vs LVDS on 10 inch and larger panels

LVDS (low-voltage differential signaling) in display use means a FlatLink or FPD-Link style link: 28 bits of parallel data serialized 7:1 onto four differential pairs plus a clock pair. TI’s SN75LVDS83B, a typical transmitter, accepts pixel clocks from 10 to 135 MHz. Faster streams use dual-link LVDS: two links side by side, each running at half the pixel rate.

eDP (embedded DisplayPort) is the VESA version of DisplayPort for built-in panels. It sends packets over up to four lanes. Earlier versions fixed the rate at 1.62, 2.7 or 5.4 Gb/s per lane, eDP 1.4 added more, and the 8b/10b coding means 80 % of the line rate carries data. Since eDP 1.3 it also supports panel self refresh: the panel’s timing controller holds a static image from its own memory, so the host link can sleep.

In our catalogue the 1920 × 1080 references sit on both sides: 12.8 inches on LVDS, 15.6 inches on eDP. Choose the one your processor has, and don’t add a bridge just because eDP is newer.

Worked example: does 1920 × 1080 at 60 Hz fit one LVDS link? The standard 1080p60 timing has a pixel rate of 148.5 MHz including blanking. That is above the 135 MHz limit of a single-link transmitter such as the SN75LVDS83B, so the panel needs dual-link LVDS: 74.25 MHz per link, with each pair carrying 7 × 74.25 = 519.75 Mb/s. Over eDP the same stream at 24 bits per pixel needs 148.5 × 24 = 3.564 Gb/s. One HBR (2.7 Gb/s) lane carries 2.7 × 0.8 = 2.16 Gb/s of data, so two lanes (4.32 Gb/s) are enough. The panel datasheet says which lane count and rate it accepts.

MIPI DSI, and bridges when host and panel don’t match

MIPI DSI carries pixels and commands over one to four high-speed lanes plus a clock. In our catalogue it covers 3.97 to 10.1 inches, and the host has to have DSI on its pins. The details are in our MIPI DSI interface guide.

When the processor has DSI but the panel you need is LVDS, a bridge chip closes the gap. TI’s SN65DSI83 takes one to four DSI lanes at up to 1 Gb/s each and drives a single LVDS link at 25 to 154 MHz, enough for 1920 × 1200 at 60 Hz with reduced blanking. It needs its own 1.8 V supply and configuration registers written at start-up (TI’s DSI-TUNER tool generates the values), and it is one more part that can go end-of-life; see display component obsolescence.

HDMI to LVDS converter boards: when they make sense

HDMI carries TMDS (transition-minimized differential signaling) video, so a converter board first decodes it. A two-chip version uses an HDMI or DVI receiver such as TI’s TFP401 (up to 165 MHz, which covers 1080p60) to produce parallel RGB, then an LVDS transmitter such as the SN75LVDS83B. Single-chip HDMI to LVDS receivers, such as Lontium’s LT8619C, combine both steps. Search terms often reverse the direction, so check the block diagram before buying a board.

A converter board makes sense when the host is a PC or a single-board computer with only HDMI at the edge, when volumes are low, or when you want to swap the computer later without touching the display. It is the wrong call in battery products, where the receiver and transmitter add power, and in long-life designs, where the board is a second item to keep in production. If the processor has LVDS or DSI on its pins, route that to the panel instead.

USB displays: a graphics chip plus a driver

With DisplayLink, the common approach to USB displays, a driver on the host reads the operating system’s frame buffer, encodes the pixels and sends them over USB. A chip on the display side decodes them into its own frame buffer and outputs a standard video signal, which still has to reach the panel through a converter. The image depends on that host driver, so check what the screen has to show before the operating system loads, and whether a driver exists for your OS.

Touch is a separate link either way. A PCAP (projected capacitive) touch controller such as the FT5446 on our S35001D reports over I²C, which suits an embedded board. A PC host will expect USB, so say so in the RFQ.

What to put in the RFQ

ItemWhy it matters
Processor part number and its display outputsDecides the native interface and whether a bridge is needed
Resolution, refresh rate and colour depth (18 or 24 bit)Sets the pixel clock, the lane count and single or dual-link LVDS
Distance between the main board and the displayLong runs favour differential links over parallel RGB
Touch interface: I²C or USBDefines the touch controller and its firmware
Converter board, if any, and who supplies itAdds power, configuration and a second lifecycle to manage
Supply rails available at the display connectorBacklight and bridge chips need their own voltages

Our TFT module RFQ guide covers the rest of the sheet, from brightness to cover glass.

Interface FAQs

Which interface options should I require for an OEM TFT display module?

Require the native panel interface your host can drive directly: SPI or parallel RGB on small panels, MIPI DSI if the processor has DSI lanes, and LVDS or eDP on large panels. Add HDMI or USB only through a converter board, and only when the host has no other display output.

Is an LVDS to HDMI converter the same thing as an HDMI to LVDS converter?

Searches use both names, but to drive a panel you need HDMI in from the host and LVDS out to the glass. Check the direction on the block diagram, the LVDS format the panel expects and the input timings the board accepts before ordering one.

Can I drive the RIN0+ to RIN2+ pairs of an LVDS panel straight from HDMI?

No. HDMI carries TMDS-encoded video, so a receiver such as the TFP401 first decodes it to parallel RGB, and an LVDS transmitter such as the SN75LVDS83B then serializes it onto the panel pairs. Single-chip HDMI-to-LVDS receivers do both steps in one part.

Do I need eDP for a 1920 × 1080 panel?

Not necessarily. Our 12.8-inch 1920 × 1080 reference S80MHJH-04-W uses LVDS and the 15.6-inch S60MZJW-01 uses eDP. Use whichever your host outputs, and check whether the LVDS panel expects a single or a dual link.

Not sure which interface your host can drive? Send the processor part number, the panel size and resolution, and the cable length. We will point you to the references that connect without a converter, or say which bridge the project needs. Browse the TFT LCD module catalogue, see custom TFT options, or ask about interface options.

Scroll to Top
Get a QuoteWhatsApp