SPI Display Modules for Microcontrollers: 1.3 to 5 Inch TFT References
SuccessLCD supplies SPI display modules as OEM references from 1.3 to 5 inches for products built around a microcontroller. On the smallest of these panels SPI carries everything, commands and pixels. On the 3.5-inch and larger references, SPI sends the set-up commands and a parallel RGB bus carries the pixels. This page lists the references, shows what SPI can and cannot refresh, and says what to send with an enquiry.
Request a quote WhatsApp +86 134 3360 8240 TFT LCD catalogue
SPI display references
| Reference | Size | Resolution | Interface | Touch |
|---|---|---|---|---|
| S130MH2ZG-03 | 1.3 in round | 240 × 240 | SPI, RGB or MCU parallel | Not fitted |
| STFT154D | 1.54 in | 240 × 240 | SPI | Confirmed for the project |
| S177MEHS-04 | 1.77 in | 128 × 160 | SPI | Not fitted |
| STFT177D | 1.77 in | 128 × 160 | SPI | Confirmed for the project |
| S350FPQI, transflective | 3.5 in | 240 × 320 | SPI + RGB | Not fitted |
| S350MLQZ | 3.5 in | 320 × 240 | SPI + RGB | Not fitted, or resistive |
| S400MHZS-03F1 | 4 in square | 480 × 480 | RGB + SPI | Capacitive |
| S500MHZI-01 | 5 in | 480 × 854 | SPI + RGB | Not fitted |
The full range is in the TFT LCD module catalogue.
SPI only, SPI + RGB, or MCU parallel
The interface follows the driver IC in the panel. A driver with built-in frame memory keeps the picture itself, so the microcontroller writes pixels over SPI only when something changes. A driver without frame memory needs a continuous stream on an RGB bus, and SPI is used once at start-up to configure it. That second kind needs a microcontroller with an RGB LCD controller and RAM for a frame buffer. MCU parallel, also called 8080, sends the same commands and pixels as SPI on an 8-bit or 16-bit bus, which is faster and costs more pins.
Worked example: full-screen refresh over SPI. Assume 16-bit colour and a 20 MHz SPI clock. The real limit comes from the driver IC datasheet and your wiring. A 128 × 160 screen is 128 × 160 × 16 = 327,680 bits, about 16 ms per frame. A 240 × 240 screen is 921,600 bits, about 46 ms, or roughly 21 frames a second. A 240 × 320 screen is 1,228,800 bits, about 61 ms, or roughly 16 frames a second. Menus and readings are comfortable at these rates, because only the changed area is redrawn. Full-screen animation at 240 × 320 and above is where SPI runs out and RGB or MCU parallel takes over.
What to confirm on an SPI display before design freeze
- The driver IC and its initialization sequence for the exact module revision.
- The SPI variant: 3-wire or 4-wire, and the logic voltage.
- For SPI + RGB panels, the RGB bus width, pixel clock and the memory your microcontroller has for a frame buffer.
- FPC pin count, pitch and contact side.
- Backlight current and how it is dimmed.
Driver ICs are compared in ILI9341 vs ST7789 vs ILI9488 and in the LCD controller and driver IC guide. Frame buffer size can be checked with the frame buffer RAM calculator.
What can be customized
The TFT cell is fixed by the panel fab. Around it, the FPC shape and connector, the backlight, a resistive or capacitive touch panel and the cover lens can be adapted. What each change involves is explained in what can be customized on a TFT module, and the general route is on the custom TFT display page. If the host is an application processor, look at a MIPI display. For larger panels in equipment, see LVDS displays.
What to send with an SPI display enquiry
- The microcontroller, the pins and memory you can spare, and the driver IC your code already supports, if any.
- The window size and the outline limits.
- Resolution, brightness and where the product is used.
- Touch and cover lens needs.
- Operating temperature range.
- Expected annual quantity and project schedule.
A fuller list is in what to include in a TFT LCD module RFQ.
FAQ
Can a microcontroller drive a TFT display over SPI?
Yes, when the panel has a driver IC with built-in frame memory. The microcontroller sends commands and pixels over SPI and redraws only what changes. At a 20 MHz clock a full 240 × 320 screen in 16-bit colour takes about 61 ms.
What is the difference between SPI and SPI + RGB on a TFT display?
On an SPI panel the same bus carries commands and pixels. On an SPI + RGB panel, SPI only configures the driver at start-up and a parallel RGB bus streams the pixels, so the host needs an RGB LCD controller and a frame buffer.
Does SuccessLCD offer MCU parallel (8080) TFT displays?
The 1.3-inch round S130MH2ZG-03 lists SPI, RGB and MCU parallel options. For other sizes the interface is confirmed for the project, because it depends on the driver IC in the panel.
Need an SPI display for your product? Send the microcontroller, the window size, the resolution and the touch you need. We will match a reference and list what has to change. Send an SPI display enquiry, or browse the TFT LCD module catalogue.
