What Should You Specify for a Transflective TFT LCD in Vehicles, Rail and Aircraft?
Specify a transflective TFT LCD by the light it will face and the standard the finished unit must pass: ambient range from night to direct sun, contrast in reflective and transmissive mode, backlight dimming range, temperature class, interface and cable run, and the environmental tests of the vehicle, rail or aircraft standard. Transflective panels earn their place where sun falls straight on the screen, because the reflective part of each pixel uses that light instead of competing with it. The price is a dimmer backlit image, so they are not the default for every cluster or cab. EN 50155, DO-160 and ISO 16750 qualify the finished unit; the module supplier provides the data those tests need. SuccessLCD supplies transflective TFT modules starting from three 3.5-inch catalogue references: the S350FPQI and S350FPQI-01 (240 × 320, SPI + RGB) and the S350FLVH-01 (480 × 640, RGB + SPI).
Request a quote WhatsApp +86 134 3360 8240 TFT LCD catalogue
What to put in the specification
Resolution, interface and touch are specified as for any TFT. These lines change when the screen goes into a car, a train cab or a cockpit.
| Item | What to write | Why it matters |
|---|---|---|
| Ambient light range | Lowest and highest illuminance at the screen, from a dark cab at night to full sun on the glass | Decides whether transflective is worth its trade-offs, and sets the backlight range |
| Contrast in each mode | Contrast ratio in reflective mode (light source and angle stated) and in transmissive mode | A backlit contrast figure says nothing about sunlight |
| Dimming range | Maximum luminance, lowest usable luminance, dimming method, NVIS class if needed | Night driving and night flying need a dim, steady image |
| Temperature | Operating and storage range, and the class the unit must meet | Ties the module to the unit’s environmental test |
| Interface and cable | Host output, cable length, and any serializer link in between | Long runs need differential or serialized links |
| End-product standard | ISO 16750 part and mounting location, EN 50155 class and EN 61373 category, or DO-160 sections | Tells the supplier which data and samples you need |
| Lifecycle | Planned production years and how change notices reach you | Vehicle and rail programs outlast many panel generations |
How a transflective pixel uses sunlight
Each pixel of a transflective LCD has two parts: a transmissive area that passes the backlight, and a reflective area with a mirror behind the liquid crystal that returns ambient light to the viewer. In the dark the backlight carries the image. In direct sun the reflector does.
Ambient light crosses the liquid crystal layer twice and backlight once, so the two areas need matched optical paths: a thinner cell gap over the reflector, patterned electrodes or a different liquid crystal mode per area (Du et al., Journal of the SID, 2010). The reflector also takes pixel area that a transmissive panel would open to the backlight. The basics of the three optical modes are in transflective vs transmissive vs reflective displays.
Start with the light range
FAA human factors guidance, citing SAE AS8034B, asks for symbology that stays readable from 1.1 lx up to sun-shafting of 86,100 lx on the display. Direct sunlight at ground level runs from 32,000 to 100,000 lx.
A transmissive display answers with backlight. Its ambient contrast ratio (ACR) is on-state luminance plus reflected light, divided by off-state luminance plus reflected light, where reflected light is the illuminance divided by π and multiplied by the panel’s luminous reflectance (Chen, Tan and Wu, Optics Express, 2017).
Worked example: how bright must a transmissive panel be at 86,100 lx? Assume 1,000:1 native contrast, a target ACR of 3:1 (the minimum the FAA guidance cites for a fixed-brightness display) and 4.4 % front reflectance, the figure Chen et al. measured on a phone LCD. Reflected luminance is 86,100 ÷ π × 0.044 = 1,206 cd/m². A 1,000 cd/m² panel then gives (1,000 + 1,206) ÷ (1 + 1,206) = 1.8:1. Reaching 3:1 takes L = 2 × 1,206 ÷ (1 − 0.003) ≈ 2,420 cd/m². With an AR-coated cover at 1.5 % reflectance, the paper’s value for single-layer MgF2 glass, reflected light falls to 411 cd/m² and about 825 cd/m² is enough.
A transflective panel skips that race. Its reflected image brightens as the sun does, so sunlit contrast does not depend on backlight power. Ask for reflective-mode contrast and reflectance with the light source and geometry stated.
Night: dimming range and NVIS
At night a transflective panel runs as a transmissive one with a smaller aperture, and the low end of the range is the harder problem. The FAA guidance asks for displays that dim far enough to keep the crew dark-adapted, with manual luminance control, and cites about 1 cd/m² as a minimum character luminance.
Write the dimming range as two numbers, maximum and lowest usable luminance, and say how the host dims: PWM or an analog control. For military aircraft, MIL-STD-3009 limits the spectral radiance, luminance and color of NVIS-compatible lighting, so the backlight and filters are designed for it from the first sample, not added late.
Temperature and the end-product standard
- Rail: EN 50155 covers electronic equipment on rolling stock and sorts it into operating temperature classes. OT3, for example, runs from −25 °C to +70 °C, with a separate switch-on condition. Shock and vibration tests come from EN 61373 (category 1 for car-body equipment), EMC from EN 50121-3-2 and fire behavior from EN 45545-2.
- Road vehicles: ISO 16750 parts 1 to 5 cover general, electrical, mechanical, climatic and chemical loads, with severity set by mounting location.
- Aircraft: RTCA DO-160 (EUROCAE ED-14) runs from temperature and altitude (section 4) and vibration (section 8) to flammability (section 26).
Check the module’s rated range against the class: a panel rated from −20 °C cannot serve a class that starts at −25 °C. Our segment LCD references for motorcycle and e-bike instruments list operating ranges from −20 to +70 °C up to −30 to +80 °C, depending on the part. For the 3.5-inch transflective TFT references, S350FPQI and S350FPQI-01 (240 × 320, SPI + RGB) and S350FLVH-01 (480 × 640, RGB + SPI), temperature range and reflectance come from the datasheet of the quoted revision.
Our group factory, Success Electronics Ltd, holds IATF 16949:2016 for the design and manufacture of LCD modules, plus ISO 9001:2015 and ISO 14001:2015. Those certify management systems. EN 50155, DO-160 and ISO 16750 test the finished unit with its housing, harness and power supply, so the module supplier’s part is data: rated temperatures, material information for the fire assessment, drawings for the vibration fixture, and samples. AEC-Q100 qualifies integrated circuits, such as the serializer in the next section, not display modules.
Interface and cable run
A small secondary display can take SPI and RGB from a nearby microcontroller, as the 3.5-inch references above do. When the screen sits away from the computer that draws it, a serializer link is one answer. TI’s DS90UB947-Q1, for example, takes an OpenLDI (LVDS) stream and sends it over FPD-Link III on 50 Ω coax or 100 Ω shielded twisted pair for up to 15 m, and is AEC-Q100 qualified to grade 2 (−40 °C to +105 °C). A deserializer at the display restores LVDS for the panel.
The RFQ should name both ends: what the host sends and what arrives at the display connector. See our guide to OEM TFT interface options for the panel side.
When a transflective panel is the wrong choice
- Direct sun never reaches the screen. A transmissive panel gives a brighter image for the same LED power.
- Video, maps or color-coded alarms must look the same day and night. Judge reflective-mode colors on a sample first.
- The screen is larger than our 3.5-inch transflective references. For a 7- or 10-inch cluster, compare a high-brightness TFT module behind an AR-coated, bonded cover, as in the worked example.
For fixed digits and icons, a monochrome transflective segment LCD is simpler still.
Transflective display FAQs
What should be considered when specifying a transflective display for an automotive instrument cluster?
Start with the light range at the screen, then ask for contrast in reflective and transmissive mode, the dimming range for night driving, the operating temperature for the mounting location under ISO 16750, and the interface and cable run from the host. Durability is proven on the finished cluster.
What is a good use for transflective LCD screens?
Fixed instruments read in direct sun: open cabs, motorcycle and e-bike dashboards, handheld meters and cockpit side panels. A shaded screen showing video is better served by a transmissive panel.
What is EN 50155?
It is the European standard for electronic equipment on railway rolling stock. It defines operating temperature classes, such as OT3 at −25 °C to +70 °C, and points to EN 61373 for shock and vibration and EN 50121-3-2 for EMC.
Can a display module be certified to EN 50155 or DO-160 on its own?
Not in the way the end product is. Both standards test the finished equipment in its enclosure and with its power supply, so the module supplier provides rated temperatures, drawings, material data and samples for the equipment maker’s tests.
Specifying a display for a cluster, cab or cockpit? Send the light range, temperature class, host interface and the standard your unit is tested to. We will say whether a transflective TFT, a segment LCD or a bonded high-brightness panel fits, and what data we can supply. See wide temperature TFT modules, browse the TFT LCD module catalogue, or send your display requirements.
