4.3 Inch Display Size: Dimensions, 480 × 272 or 800 × 480, and the RGB Interface
A 4.3 inch display measures 109.2 mm across the diagonal of its active area, about 95 × 54 mm of image at 480 × 272 or 94 × 56 mm at 800 × 480, and SuccessLCD’s 4.3 inch references, such as the S430MI2NI (480 × 272, RGB) and the S430MBWS-01 (800 × 480, RGB), have a 105.5 × 67.2 mm module outline. All six 4.3 inch TFTs in the catalogue use a parallel RGB interface, without touch, with resistive touch or with capacitive touch. Which resolution you can use is mostly decided by the memory in your host.
Request a quote WhatsApp +86 134 3360 8240 TFT LCD catalogue
4.3 inch display dimensions: active area vs module outline
The size in the name is the nominal diagonal of the active area, the part of the glass that has pixels. The outline of the module adds the glass edge, the black border, the backlight frame and the bend of the FPC (flexible printed circuit), so it is the number your mechanical engineer needs, and it comes from the drawing, not the diagonal.
The active area follows from the diagonal and the pixel count, assuming square pixels:
| 480 × 272 | 800 × 480 | |
|---|---|---|
| Aspect ratio | 30:17 (close to 16:9) | 5:3 |
| Active area (nominal) | 95.0 × 53.9 mm | 93.7 × 56.2 mm |
| Pixel pitch | 0.198 mm | 0.117 mm |
| Pixel density | about 128 ppi | about 217 ppi |
| Module outline, our references | 105.5 × 67.2 mm | 105.5 × 67.2 mm |
So the outline adds roughly 10 to 12 mm in width and 11 to 13 mm in height around the image. Where that border sits, and which side the FPC leaves from, is on the drawing for each part number. The nominal figures above are for early layout only.
480 × 272 or 800 × 480 on a 4.3 inch TFT display
An 800 × 480 panel has 384,000 pixels, 2.9 times as many as 480 × 272. On the same 4.3 inch glass that buys sharper text and finer lines. It also costs memory and bus bandwidth in the host, which is where small projects get stuck.
Worked example: memory, clock and viewing distance. One 16-bit (RGB565) frame is 480 × 272 × 2 = 261,120 bytes, against 800 × 480 × 2 = 768,000 bytes. With 24-bit colour stored as 3 bytes per pixel, it is 391,680 and 1,152,000 bytes. Double buffering doubles all four numbers. For the pixel clock, assume total timings of 525 × 286 clocks for 480 × 272 and 1056 × 525 for 800 × 480, including blanking (check your panel’s timing table). At 60 Hz that is 525 × 286 × 60 = 9.0 MHz and 1056 × 525 × 60 = 33.3 MHz. For viewing distance, normal vision resolves about one arc-minute, roughly 0.29 mm at 1 m. A 0.198 mm pitch stops showing individual pixels beyond about 0.68 m, and 0.117 mm beyond about 0.40 m.
A wall controller read from a metre away looks fine at 480 × 272. A handheld instrument read at 30 to 40 cm, with small numbers and graphs, is where 800 × 480 earns its memory. If the host can handle 800 × 480 but users need everything drawn larger, a 5 inch 800 × 480 panel such as S500MIWI-04 gives the same pixel count at a 0.136 mm pitch; see the 5 inch TFT guide.
4.3 inch TFT references in our catalogue
| Model | Resolution | Interface | Touch | Body (reference) |
|---|---|---|---|---|
| S430MBWS-01 | 800 × 480 | RGB | None fitted | 105.5 × 67.2 mm |
| S430MI2NI | 480 × 272 | RGB | None fitted | 105.5 × 67.2 mm |
| S430MINS-02 | 480 × 272 | RGB | None fitted | 105.5 × 67.2 mm |
| S430MINS-15 | 480 × 272 | RGB | None fitted | 105.5 × 67.2 mm |
| STFT43-02D | 480 × 272 | RGB | Capacitive | Confirmed per project |
| STFT43D | 480 × 272 | RGB | Resistive | Confirmed per project |
For the STFT43 parts, brightness, driver IC, viewing angle and temperature range are confirmed against the datasheet when we quote, so ask for it with the drawing.
The 4.3 inch TFT LCD display interface: parallel RGB
Parallel RGB sends every pixel, every frame, on a data bus clocked by PCLK, with HSYNC, VSYNC and often a data-enable (DE) line marking the active pixels. The panel holds no image of its own, so the host has to keep refreshing it from a frame buffer, usually by DMA. Espressif’s documentation for the ESP32-S3 is a good worked reference: it supports 16-bit RGB565 natively and keeps the frame buffer in PSRAM by default.
- Pins. A 16-bit bus with PCLK, HSYNC, VSYNC and DE is 20 signals; 24-bit is 28. Plan the GPIO budget before choosing the MCU.
- Bus width vs colour depth. If the board routes 16 or 18 data lines, the firmware must not be set for 24-bit output. Espressif’s notes say the same.
- Initialization. Some RGB panels need commands over SPI first. Our 4.3 inch references are listed as RGB only; the datasheet confirms whether any set-up is needed.
- Timing. DE mode and SYNC mode use the porch values differently. Copy them from the panel’s timing table, then check the result with our pixel clock calculator.
If the processor has no RGB controller at all, 4.3 inches is the wrong size to force. SPI-only panels in our catalogue stop at 1.77 inches, and the 3.5 inch range adds RGB with SPI; see the 3.5 inch display guide. The other way out is a processor with MIPI DSI or LVDS and a larger panel.
Touch: none, resistive or capacitive
A resistive panel such as STFT43D responds to pressure, so it works with gloves and a stylus. A capacitive panel such as STFT43-02D sits behind a glass cover and supports multi-touch, but needs tuning for gloves, water and thick covers. Our comparison of capacitive vs resistive touch screens covers the trade in detail. If the product needs a printed cover lens or a different touch controller, treat it as a customization from the start rather than adding it later.
When 4.3 inches is the wrong choice
- The housing is narrower than about 106 mm. Look at 3.5 inches.
- The interface needs long lists or a full on-screen keyboard. A 7 inch 800 × 480 or 1024 × 600 panel gives room; see the 7 inch display guide.
- The display sits far from the main board. A parallel RGB bus is meant for short connections; for a longer cable a differential link is the usual answer, for example the 5 inch LVDS reference S500MHWS2-01.
- The host has 512 KB of RAM or less and no external memory. Use 480 × 272 at 16-bit, or a smaller SPI panel.
4.3 inch display FAQs
What is the size of a 4.3 inch display in mm?
The 4.3 inches is the diagonal of the active area, 109.2 mm. That gives an image of about 95.0 × 53.9 mm at 480 × 272 and 93.7 × 56.2 mm at 800 × 480. The module outline is larger; our 4.3 inch references measure 105.5 × 67.2 mm.
What resolution is a 4.3 inch TFT display?
The two common ones are 480 × 272 and 800 × 480, and our six 4.3 inch references use one or the other. At this size that is about 128 and 217 pixels per inch.
Can a microcontroller drive a 4.3 inch 800 × 480 display?
Yes, if it has an RGB LCD controller and enough memory for the frame buffer. One 16-bit frame at 800 × 480 is 768,000 bytes, which usually means external SDRAM or PSRAM. At 480 × 272 the same frame is 261,120 bytes.
Is a 4.3 inch display 16:9?
Close, at 480 × 272, which is 30:17. The 800 × 480 panels are 5:3, so for the same 4.3 inch diagonal their image is about 1.4 mm narrower and 2.3 mm taller. Check the drawing before you fix the window in the housing.
Can SuccessLCD supply a 4.3 inch display with touch or a custom cover glass?
Yes. STFT43-02D has capacitive touch and STFT43D resistive touch, both 480 × 272 with an RGB interface. The cover glass, FPC, backlight and touch tuning can be adapted per project, while the panel resolution and interface stay as listed.
Who holds the quality certificates?
The group factory, Success Electronics Ltd, is certified to IATF 16949:2016, ISO 9001:2015 and ISO 14001:2015. The certificates are issued to the factory, not to the Hong Kong trading company.
Choosing a 4.3 inch TFT? Send the processor, the memory available, the housing window and the touch you need. We will suggest the 4.3 inch reference that fits and send its drawing. Browse the TFT LCD module catalogue or ask about a 4.3 inch display.
