VA LCD Displays: Negative Segment LCD References for OEM Products

SuccessLCD supplies custom VA LCD displays for OEM products, with catalogue references such as the S3959D (VA negative, 154.21 × 86.61 mm viewing area, 1/4 duty, −20 to +70 °C) for thermostats and the S4533D (151.95 × 65.0 mm, −30 to +80 °C) for motorcycle instruments. A VA (vertical alignment) LCD in negative mode shows lit digits and icons on a black background, so the glass looks like a dark window when the product is off. Like any segment LCD it is drawn for one product: the references show a finished VA design at a given size, drive and connection, and a new project starts from your artwork.

Request a quote Monochrome LCD catalogue

Viewing areas of six VA LCD references drawn to the same scaleSix dark rectangles at one scale: S3959D thermostat 154.21 by 86.61 mm, S4533D motorcycle instrument 151.95 by 65 mm, S4388D blood pressure monitor 124.2 by 80.7 mm, S4148D vehicle dashboard 99 by 49 mm, S4054D thermostat 68.4 by 59.35 mm and S4015D food hygrometer 45.25 by 16.59 mm.VA LCD references: minimum viewing area, to scaleS3959DThermostats154.21 × 86.61 mmS4533DMotorcycle instruments151.95 × 65 mmS4388DBlood pressure monitors124.2 × 80.7 mmS4148DVehicle dashboards99 × 49 mmS4054DThermostats68.4 × 59.35 mmS4015DFood hygrometers45.25 × 16.59 mmMinimum viewing area from each product drawing, all drawn at 1.4 px per mm. Black areas show the unlit VA glass.
Figure: the minimum viewing area of six VA references at one scale, from a 45 mm hygrometer display to a 154 mm thermostat display. Each is a finished custom design.

VA LCD display references

All nine references are VA negative displays from the SuccessLCD catalogue. Values come from each product drawing; the viewing area is the minimum area that must stay visible in the window.

ReferenceUsed inViewing areaGlass outlineVoltage, driveOperating temp.Connection
S3959DThermostats154.21 × 86.61 mm157.21 × 94.61 mm3.3 V, 1/4 duty, 1/3 bias−20 to +70 °CMetal pins, 2.54 mm
S4054DThermostats68.4 × 59.35 mm75.4 × 62.35 mm5.0 V, 1/8 duty, 1/4 bias−20 to +70 °CMetal pins, 2.54 mm
S4533DMotorcycle instruments151.95 × 65.0 mm154.95 × 70.0 mm5.0 V, 1/4 duty, 1/3 bias−30 to +80 °CMetal pins, 2 mm
S4148DVehicle dashboards99.0 × 49.0 mm103.0 × 58.0 mm5.0 V, 1/4 duty, 1/3 bias−20 to +70 °CMetal pins, 2.54 mm
S4388DBlood pressure monitors124.2 × 80.7 mm127.2 × 86.2 mm3.3 V, 1/8 duty, 1/3 bias−10 to +60 °CHeat seal, 1 mm
S3705DMeasuring instruments77.0 × 50.0 mm80.0 × 57.0 mm5.0 V, 1/8 duty, 1/4 bias−20 to +70 °CMetal pins, 1.8 mm
S3321DPower supplies90.0 × 30.5 mm96.0 × 37.5 mm4.5 V, 1/4 duty, 1/3 bias−20 to +70 °CMetal pins, 2.54 mm
S4087DMassage devices83.6 × 58.6 mm87.6 × 66.6 mm5.0 V, 1/4 duty, 1/3 bias0 to +50 °CMetal pins, 2.54 mm
S4015DFood hygrometers45.25 × 16.59 mm48.25 × 21.09 mm3.3 V, 1/4 duty, 1/3 bias−10 to +60 °CZebra, 2 mm

SuccessLCD keeps more than 120 VA references on drawing. Others are grouped by product on the thermostat LCD displays and motorcycle instrument LCD pages, and the full list is in the monochrome LCD catalogue.

How a VA LCD differs from TN and STN

In a VA cell the liquid crystal stands upright between the glass plates when no voltage is applied. Between crossed polarizers that blocks the backlight, so the unlit glass is black, and a driven segment tilts the molecules and lets light through. Positive TN, HTN and STN glass works the other way round: dark segments on a light background, readable by room light with a reflective rear polarizer. In practice:

  • A VA negative display is read by its backlight. Eight of the nine references have transmissive polarizers front and rear; the S4148D has a transflective rear polarizer, so it stays readable in daylight with the backlight off.
  • The black background hides the segment pattern when the product is switched off, which suits thermostats, appliances and dashboards behind a dark or smoked lens.
  • The digits take the colour of the backlight, so one glass layout can be built with white, amber or another LED colour.

The monochrome modes and how they compare on cost are set out in monochrome LCD types.

Drive, voltage and connection

The references run at 3.3 to 5.0 V with 1/4 or 1/8 duty. The duty sets how many common electrodes share each segment line and therefore how many pins the glass needs. Higher duty saves pins and costs contrast margin, as the duty and bias guide explains.

Worked example: pins for a 96-segment thermostat layout

Say the artwork has 96 segments for digits, icons and units. At 1/4 duty each segment line serves four segments: 96 ÷ 4 = 24 segment lines plus 4 commons, 28 pins. At 1/8 duty it is 96 ÷ 8 = 12 segment lines plus 8 commons, 20 pins. The two thermostat references show both choices: the large S3959D runs at 1/4 duty and 3.3 V, the S4054D at 1/8 duty and 5.0 V. Check the duty, bias and voltage your controller supports before the pin map is drawn.

Most references use metal pins at 2.54, 2 or 1.8 mm pitch that solder into the board. The S4388D uses a heat-seal connector at 1 mm pitch, and the S4015D a zebra connector held in compression by the housing; the zebra connector guide covers the design rules.

What can be customized

  • The artwork: digits, icons, legends, units and their positions.
  • Glass outline, window and viewing direction (the references use 6 o’clock or 12 o’clock).
  • Polarizers: transmissive on both sides, or a transflective rear polarizer as on the S4148D.
  • Drive condition, voltage and pin map, matched to your controller.
  • Connection: metal pins, zebra, heat seal or FPC.
  • Backlight colour and current, and the operating range within what the liquid crystal allows; the references above run from 0 to +50 °C up to −30 to +80 °C.

A change to the artwork after tooling means new glass, so freeze the drawing first. What drives the tooling and unit cost is covered in custom LCD display cost, and the development route is on the custom segment LCD page.

When a TFT is the better choice

A VA segment display can only show what is drawn on the glass. If the product needs menus, graphs, several languages or animation, a TFT module fits better. The smart home touch panel displays page lists 1.8 to 5 inch TFT references for wall panels and thermostats, and IPS TFT displays keep the picture readable from every side. The full range is on the TFT LCD modules page.

What to send with a VA LCD enquiry

  • A sketch or drawing of the digits, icons and legends, even a hand drawing.
  • The window size and the outline limits in your housing.
  • Backlight colour, and whether the display must be readable with the backlight off.
  • The controller or driver IC, with the duty, bias and voltage it supports.
  • Operating temperature range and viewing direction.
  • Connection type, expected annual quantity and project schedule.

FAQ

What is a VA LCD?

A VA (vertical alignment) LCD keeps its liquid crystal upright when no voltage is applied, so between crossed polarizers the unlit glass looks black. In a segment display this gives the negative look: bright digits and icons on a dark background, lit by the backlight.

Does a VA LCD need a backlight?

With transmissive polarizers, yes, because the digits are lit only by the backlight. A transflective rear polarizer, as on the S4148D, keeps the display readable in ambient light when the backlight is off.

Can SuccessLCD make a VA LCD to my own artwork?

Yes. Send the artwork, window size, controller and temperature range, and the glass is drawn to your layout. A reference of similar size from the table above is a useful starting point for the drive, voltage and connection.

Who holds the quality certificates?

The group factory, Success Electronics Ltd, is certified to IATF 16949:2016, ISO 9001:2015 and ISO 14001:2015. The certificates are issued to the factory, not to the Hong Kong trading company.

Planning a VA LCD? Send the artwork, window size, controller and temperature range. SuccessLCD will suggest a close VA reference and draw the glass to your layout, or browse the monochrome LCD catalogue first.

Request a quote

Scroll to Top
Get a QuoteWhatsApp