Display Kits for SBC and SoM Makers: MIPI DSI, LVDS and RGB TFT Modules
If you sell single-board computers or system-on-modules, the display in your evaluation kit is often the first thing a customer judges your board by. It has to light up on your reference BSP the day the kit ships, match the connector you already put on the carrier board, and still be orderable when your customer moves to production two years later. We supply TFT modules for that job: a catalogue panel with touch fitted, an adapter FPC or small board mapped to your connector, and the timing, initialization and touch data your software team needs. Production orders start at 1,000 pieces.
Request a quote WhatsApp +86 134 3360 8240 TFT LCD catalogue
Start from the interface your board already has
Most kit projects begin with a board that is already laid out, so the display has to fit the interface and connector that exist. The table lists catalogue references by interface. All of them can take an adapter to a different connector.
| Board interface | Usual size range | Catalogue references |
|---|---|---|
| MIPI DSI (2 or 4 lanes) | 4 to 10.1 in | STFT397D (3.97 in, 480 × 800, capacitive), S400MB1ZS-01F2 (4 in square, 720 × 720, capacitive), S550MEKI-01 (5.5 in, 720 × 1280), STFT1010D (10.1 in, 800 × 1280, capacitive) |
| LVDS, single link | 7 to 12.1 in | S700MB1XH-09 (7 in, 1024 × 600), S10MB1XH-07C0 (10.1 in, 1024 × 600, capacitive), S10MHYH-02 (12.1 in, 1280 × 800) |
| LVDS at 1080p, or eDP | 12.8 to 15.6 in | S80MHJH-04-W (12.8 in, 1920 × 1080, LVDS), S60MZJW-01 (15.6 in, 1920 × 1080, eDP) |
| Parallel RGB | 4.3 to 7 in | STFT43-02D (4.3 in, 480 × 272, capacitive), S500MIWI-04 (5 in, 800 × 480), S700MIWN-18-W (7 in, 800 × 480) |
| SPI or SPI + RGB, for microcontroller boards | 1.3 to 5 in | S400MHZS-03F1 (4 in square, 480 × 480, capacitive), S500MHZI-01 (5 in, 480 × 854) |
The full lists are on the MIPI DSI, LVDS, RGB and SPI pages. If your carrier board offers two interfaces, pick the one your BSP already supports well, not the one with the shortest datasheet.
Check the link budget before you pick the panel
The question that decides most kit displays is whether the host can drive the panel’s pixel clock on the lanes or link it has. Two worked examples, with typical blanking values. Use the real ones from the panel’s timing table, or run them through our pixel clock calculator.
MIPI DSI, 800 × 1280 at 60 Hz. With a horizontal total of 880 and a vertical total of 1316, the pixel clock is 880 × 1316 × 60 = 69.5 MHz. At 24 bits per pixel that is 1.67 Gbit/s of pixel data. Spread over 4 lanes it is about 417 Mbit/s per lane; over 2 lanes, about 834 Mbit/s per lane, before packet overhead. A board that brings out only 2 lanes can still run this panel if its DSI host is rated well above 834 Mbit/s per lane. If it is not, plan on 4 lanes.
LVDS, 1024 × 600 and 1920 × 1080. A 1024 × 600 panel with totals of 1344 × 635 runs at 1344 × 635 × 60 = 51.2 MHz, comfortably inside a single LVDS link. A 1920 × 1080 panel on the common 2200 × 1125 timing needs 148.5 MHz, which most hosts cannot send down one link, so 1080p LVDS panels normally run dual link at 74.25 MHz per link. If your board has one LVDS link, stay at 1280 × 800 or below, or use eDP.
More on lanes and video versus command mode is in our MIPI DSI guide, and on LVDS cable and layout in LVDS EMI and signal integrity.
What should be in the box, and in the download
A display that works on the bench in your lab but not on a customer’s desk usually fails on something small: a reset line pulled the wrong way, a touch controller at a different I²C address than the driver expects, or a backlight that needs a voltage the carrier board does not have. Agree these points before the first sample is built:
- Panel with touch fitted. Most kit customers expect capacitive touch. Confirm the touch controller’s I²C address, interrupt and reset lines, and whether its configuration is stored in the controller or loaded by the host.
- Adapter to your connector. An FPC tail can be lengthened, reshaped or re-pinned on a catalogue panel; a small adapter board can also carry a backlight driver or level shifting. The cell size itself cannot change (see what can be customized on a TFT module).
- Backlight drive. State whether your board supplies the LED current or only an enable and PWM signal. A 10-inch backlight typically needs a boost converter that small carrier boards do not have.
- Timing table and initialization sequence. These are the values your engineer puts into the panel driver or device tree: pixel clock, porches, sync widths and polarity, and for MIPI panels the command sequence that wakes the driver IC.
- Controlled outline drawing. Kit customers design enclosures around your display. The drawing they get should carry a revision, and that revision should only move with a change notice.
Kits sell for years: lifecycle terms matter more than unit price
A customer who designs your SoM into a product will often want the same display, because it is the one your BSP supports. That turns a kit accessory into a production part with a five-year tail. Ask for three things in the supply agreement: a written change notice before any change to materials, process or drawing; a last-time-buy window if a part goes end of life; and a named alternative with the same outline and connector where one exists. Our page on component obsolescence in TFT displays explains what usually goes end of life first, and OEM vs ODM covers who owns the drawing.
Quantities, samples and what to send
We work on OEM terms: production orders start at 1,000 pieces, and evaluation samples are arranged per project before an order. The group factory that builds our modules holds IATF 16949, ISO 9001 and ISO 14001 certificates. To quote a kit display, send:
- The board’s display interface, lane count or link type, and the connector part and pinout you want to keep.
- Target size and resolution, and whether the panel is used in portrait or landscape.
- Touch: capacitive or none, cover glass thickness if you have one in mind.
- Backlight supply available on the carrier board.
- Expected yearly quantity for kits, and for customers who go to production on your module.
SBC and SoM display kit FAQs
What should a display kit for a SoM or SBC include?
A panel with touch fitted, an adapter to the board’s connector, a way to drive the backlight, and the files the software team needs: timing table, initialization sequence, touch configuration and a controlled outline drawing.
Should a SoM display use MIPI DSI or LVDS?
MIPI DSI suits panels up to about 10 inches on boards whose processor has a DSI port. LVDS suits 7 to 15.6 inch panels and longer cables. Check the pixel clock against the host’s lane rate or link limit before choosing.
Can the FPC be changed to match our existing display connector?
Yes, within limits. On a catalogue panel the FPC tail length, shape and pin assignment can usually be changed, or a small adapter board added. The size of the LCD cell cannot be changed.
What is the minimum order for a kit display?
Production orders start at 1,000 pieces. Evaluation samples are arranged per project before an order is placed.
Building a display kit for your board? Send the interface, connector pinout, size and yearly volume, and we will propose a catalogue panel with the adapter and files to match. Ask about a display kit.
