Custom Touch Screen Displays for OEM Products

SuccessLCD supplies custom touch screen displays for OEM products, starting from catalogue modules such as the S35001D (3.5-inch, 320 × 240, RGB, G+G capacitive touch) and the S10MB1XH-07C0 (10.1-inch, 1024 × 600, LVDS, capacitive touch). The display cell and the touch type come from an existing reference; the cover lens, touch tuning, FPC, backlight and bonding are adapted to your enclosure. Below are the references, the limits, and what to send so a quote can start.

Request a quote Touch panel and cover lens options

Thickness of the S35001D touch display stackThree stacked layers drawn to a common vertical scale: a 3.10 mm TFT module at the bottom, about 0.90 mm of sensor glass and adhesive, and a 0.70 mm cover lens on top. Arrows show 3.10 mm for the module, 1.60 mm added by touch and lens, and 4.70 plus or minus 0.50 mm in total.S35001D: how much depth the touch stack addsTFT module (LCM): 3.10 ± 0.20 mmSensor glass and adhesive: about 0.90 mmCover lens: 0.70 mm3.10 mm+1.60 mm4.70± 0.50Values from the S35001D drawing (V00). The 0.90 mm layer is found by subtraction, not measured.Vertical scale only; the outline is not to scale.
Figure: the S35001D is 3.10 mm thick without touch and 4.70 mm with its G+G capacitive touch and 0.70 mm cover lens fitted.

Touch TFT display references

These SuccessLCD references are touch TFT displays, shipped with the touch panel fitted. Each row links to its product page; values marked per project come from the datasheet of the quoted revision.

ReferenceSizeResolutionInterfaceTouchOutlineBrightness, temperature
S240MCQS-18P2.4 inPer projectPer projectResistive42.72 × 60.26 mmPer project
S35001D3.5 in320 × 240RGBCapacitive, G+G, FT5446-P03 on I²C76.96 × 63.96 × 4.70 mm850 cd/m² typ.; −20 to +70 °C
S400MBZS-01D4 in square480 × 480RGB + SPICapacitive83.7 × 83.7 mmPer project
STFT43D4.3 in480 × 272RGBResistivePer projectPer project
STFT43-02D4.3 in480 × 272RGBCapacitivePer projectPer project
STFT50-02D5 in800 × 480RGBCapacitive, mirror cover glassPer projectPer project
S500MI4WS2-03F15 inPer projectPer projectCapacitive120.7 × 80.44 mmPer project
S700MIWE-28C07 inPer projectPer projectCapacitive164.9 × 100 mmPer project
STFT80D8 inPer projectPer projectCapacitivePer projectPer project
S10MB1XH-07C010.1 in1024 × 600LVDSCapacitive235 × 143 mmPer project

Only need the touch layer? The S700GG-42 (7-inch class, GT911 on I²C) and S10GF2-94 (10-inch class, FT5426G on I²C) are standalone capacitive panels for a display you already use. Lens shapes and coatings are covered on the touch panel and cover lens page.

What can change, and what stays fixed

Around the display cell, most of the front stack is open to change:

  • Cover lens: outline, thickness, holes, printed border and logo, and an AG, AR or AF surface.
  • Touch type: projected capacitive or resistive, with the controller reporting over I²C or USB.
  • Touch tuning for the final cover thickness, gloves or water. See capacitive touch with gloves, water and thick glass.
  • Bonding: an air gap with frame tape, or optical bonding with OCA or resin.
  • FPC length, exit side, connector and pin order, and the backlight LED count and current.

The TFT cell itself is made by the panel fab in fixed sizes, so its diagonal, resolution and display interface are chosen from existing cells, not designed. A different cell usually means a new sensor and cover lens too, because both are sized to the display’s viewing area. The full list is in what can be customized on a TFT module.

Capacitive or resistive, full module or touch only

A projected capacitive (PCAP) touch panel senses the finger through glass, so the front can be a flat, hard cover with multi-touch gestures. Gloves, water and thick covers shift its behaviour, so the controller is tuned with the final lens. Resistive touch responds to pressure, works with any glove or stylus, and suits single-touch controls; the cost is a softer top film and slightly less light through it. The longer comparison is in capacitive vs resistive touch screens.

Buying the display with touch fitted keeps one drawing for the whole stack, so outline, thickness and optics are checked together. Adding a standalone panel to a display you have already qualified also works, but then your team stacks the lens, sensor and display tolerances.

Worked example: enclosure depth for the S35001D

The drawing gives 3.10 ± 0.20 mm for the module without touch and 4.70 ± 0.50 mm with touch and lens fitted. The touch stack therefore adds 4.70 − 3.10 = 1.60 mm nominal, of which 0.70 mm is the cover lens; the remaining 0.90 mm is sensor glass and adhesive. For the pocket, design to the upper limit: 4.70 + 0.50 = 5.20 mm, plus whatever gasket or tape sits on the lens.

What to send with a touch screen display enquiry

  • The window size or the closest reference from the table above.
  • The host processor, the display interface it drives, and the touch interface it expects.
  • Capacitive or resistive, the number of touch points, and whether users wear gloves or the screen gets wet.
  • The cover lens drawing: outline, thickness, printing, surface treatment and any impact target.
  • Brightness, operating temperature range, and air gap or optical bonding.
  • Expected annual quantity and the project schedule.

A fuller checklist is in what to include in a TFT LCD module RFQ.

FAQ

Can SuccessLCD make a custom touch screen display from a catalogue module?

Yes. The display cell and touch type come from a reference such as the S35001D or S10MB1XH-07C0, and the cover lens, touch tuning, FPC, backlight and bonding are adapted to the product. The cell size and resolution are chosen from existing panels.

Can I get a sample before committing to a custom touch display?

Start with an evaluation sample of the closest catalogue reference. New parts such as a printed cover lens or a resized sensor are built after their drawing is approved, so those samples follow later in the project.

Can you add touch to a display we already use?

Often, yes. A standalone capacitive panel such as the S700GG-42 or S10GF2-94 can be matched to the display outline and viewing area. The lens, controller, connector and mechanical fit still need to be checked in your product.

Do your touch screen displays use a PCAP touch panel?

The capacitive references do. They use a projected capacitive (PCAP) touch panel, for example a G+G sensor with an FT5446-P03 controller over I²C and a 0.70 mm cover glass on the S35001D. Resistive references such as the S350MLQZ variant are there for gloved or stylus use.

What is a touch TFT display?

A touch TFT display is a TFT LCD module with the touch panel already mounted, tested and supplied as one part. The S35001D, for example, combines a 3.5-inch 320 × 240 RGB TFT with a G+G capacitive touch panel; resistive versions suit gloves and styluses.

Who holds the quality certificates?

The group factory, Success Electronics Ltd, is certified to IATF 16949:2016, ISO 9001:2015 and ISO 14001:2015. The certificates are issued to the factory, not to the Hong Kong trading company.

Planning a touch screen display? Send the window size, host, touch type and cover lens drawing. SuccessLCD will match a catalogue reference and list what has to change, or browse the TFT LCD module catalogue first.

Request a quote

Scroll to Top
Get a QuoteWhatsApp