TFT LCD Manufacturer for OEM Display Modules
SuccessLCD is a TFT LCD manufacturer for OEM display modules, with catalogue references from the 1.3-inch round S130MH2ZG-03 (240 × 240, SPI / RGB / MCU) to the 15.6-inch S60MZJW-01 (1920 × 1080, eDP). Production is at the group factory, Success Electronics Ltd, with authorized partners where a project needs a specific process. Each module is built around a TFT cell from a panel fab, so the backlight, FPC, touch panel, cover lens, bonding and frame can change for your product while the cell size and resolution stay as listed.
Request a quote WhatsApp +86 134 3360 8240 TFT LCD catalogue
What a TFT LCD manufacturer actually builds
The word manufacturer covers two different factories. A panel fab makes the TFT cell: two glass plates with the transistors, colour filter and liquid crystal, cut from large substrates in fixed sizes and resolutions. A module manufacturer turns that cell into a part you can design in. It adds the FPC and driver connection, the LED backlight and the frame, and where needed a touch panel, cover lens and optical bonding.
SuccessLCD works on the module side. A new cell size needs its own photomasks and fab runs, which only pays off at very large volumes, so a custom TFT project starts by choosing the existing cell closest to your window and resolution. The LCD module manufacturers guide explains how panel makers, module makers and custom suppliers differ, and the TFT LCD module manufacturing process shows the assembly steps.
TFT reference modules from 1.3 to 15.6 inches
SuccessLCD keeps more than 50 TFT references on drawing. The twelve below cover the range of sizes and interfaces; values are from each product page.
| Reference | Size | Resolution | Interface | Touch | Body outline |
|---|---|---|---|---|---|
| S130MH2ZG-03 | 1.3 in, round | 240 × 240 | SPI / RGB / MCU | Not fitted | 35.9 × 39.7 mm |
| S177MEHS-04 | 1.77 in, portrait | 128 × 160 | SPI | Not fitted | 34.7 × 46.7 mm |
| S35001D | 3.5 in | 320 × 240 | 24-bit RGB + SPI | Capacitive, G+G | 76.96 × 63.96 mm |
| S400MHZS-03F1 | 4 in, square | 480 × 480 | RGB + SPI | Capacitive | 83.7 × 83.7 mm |
| S430MBWS-01 | 4.3 in | 800 × 480 | RGB | Not fitted | 105.5 × 67.2 mm |
| S500MHZI-01 | 5 in, portrait | 480 × 854 | SPI + RGB | Not fitted | 66.4 × 120.05 mm |
| S550MEKI-01 | 5.5 in, portrait | 720 × 1280 | MIPI | Not fitted | 70.25 × 127.61 mm |
| S700MI2XE-02 | 7 in | 1024 × 600 | RGB | Not fitted | 164.8 × 99.8 mm |
| S10MB1XH-07C0 | 10.1 in | 1024 × 600 | LVDS | Capacitive | 235 × 143 mm |
| S10MHYH-02 | 12.1 in | 1280 × 800 | LVDS | Not listed | 277.7 × 180.6 mm |
| S80MHJH-04-W | 12.8 in | 1920 × 1080 | LVDS | Not listed | 294.4 × 175 mm |
| S60MZJW-01 | 15.6 in | 1920 × 1080 | eDP | Not fitted | 350.7 × 205.27 mm |
The S35001D page carries the full drawing data: 850 cd/m² typical from six white LEDs, −20 to +70 °C operating range and a G+G capacitive touch panel on I²C. For most other references the page lists size, resolution, interface and outline, and brightness and temperature range are confirmed from the datasheet of the revision you quote. The full list, with filters, is in the TFT LCD module catalogue.
What can be customized around the cell
- Backlight: LED count, LED current and optical films. More brightness costs power and heat.
- FPC: length, shape, exit side, connector and pin order, with room for small parts such as an LDO or a bridge IC.
- Interface: set by the driver IC. Another host interface needs a bridge chip on the FPC or an adapter board.
- Touch: PCAP or resistive, with the controller and its interface chosen for your host.
- Cover lens: shape, thickness, holes, black border and logo printing, AG, AR or AF coatings.
- Optical bonding with OCA or liquid resin instead of an air gap.
- Frame and mounting: metal frame, ears, adhesive tape and gaskets.
- Initialization code: timing, orientation, gamma and voltages.
Two things stay with the cell: the liquid crystal mode and viewing angle (TN or IPS), and most of the temperature range, which depends on the liquid crystal and polarizers. A heater can extend the cold end. Each change and what it affects elsewhere is covered in custom TFT LCD modules: what can be customized, and the engineering route is on the custom TFT page.
Matching the interface to the resolution
The interface follows the pixel rate. A small SPI display moves a few hundred kilobits per frame, a full HD panel close to three gigabits per second.
Worked example: raw pixel data at 60 frames per second
Active pixels only, 24-bit colour. The 4.3-inch S430MBWS-01 at 800 × 480: 800 × 480 × 60 = 23.0 million pixels per second, times 24 bits = 553 Mbit/s. The 7-inch S700MI2XE-02 at 1024 × 600: 36.9 million pixels per second = 885 Mbit/s. The 15.6-inch S60MZJW-01 at 1920 × 1080: 124.4 million pixels per second = 2.99 Gbit/s. At the small end, one 128 × 160 frame of the S177MEHS-04 at 16-bit colour is 327,680 bits, so 30 frames per second stays under 10 Mbit/s. Blanking adds to all of these, so take the real pixel clock from the timing table in the datasheet.
The catalogue follows the same pattern: SPI on the smallest displays, parallel RGB up to 7 inches at 1024 × 600, LVDS from 5 to 12.8 inches, and eDP on the 15.6-inch full HD part. MIPI DSI appears where a high pixel count sits in a small outline, as on the 5.5-inch S550MEKI-01 at 720 × 1280. The trade-offs are compared in the TFT interface guide.
Certificates, documents and samples
- The group factory, Success Electronics Ltd, is certified to IATF 16949:2016 for the design and manufacture of LCD modules, and to ISO 9001:2015 and ISO 14001:2015. The certificates are issued to the factory, not to the Hong Kong company.
- Each reference carries a drawing revision, for example Drawing V00 · 2026-05-09A on the S35001D. Ask for the controlled drawing and specification of the exact revision you will buy.
- Agree before sampling what will be checked: appearance, electrical behaviour, mechanical fit and the validation your product needs.
- Ask how changes to glass, driver IC, backlight or materials are notified. Lifecycle planning is covered in component obsolescence in LCD and TFT displays.
What to send with a TFT enquiry
- Window size or outline limits, and the size range you can accept.
- Resolution, and the host interface you have: SPI, RGB, MIPI DSI, LVDS or eDP.
- Touch: none, PCAP or resistive; glove or water use; cover lens thickness.
- Brightness target and where the product is used: indoors, near a window or outdoors.
- Operating temperature range.
- FPC exit, connector and the board space behind the display.
- Expected annual quantity and project schedule.
A longer checklist is in what to include in a TFT LCD module RFQ.
FAQ
Does SuccessLCD make the TFT glass?
No. The TFT cell comes from panel fabs in fixed sizes and resolutions. SuccessLCD builds the module around it at the group factory, Success Electronics Ltd: backlight, FPC, frame, touch panel, cover lens and bonding.
Can you customize an existing TFT module?
Yes. The backlight, FPC, touch panel, cover lens, optical bonding, frame and initialization code can change. The cell size, resolution and liquid crystal mode stay fixed, so start from the reference closest to your window.
What TFT sizes and interfaces does SuccessLCD offer?
The published references run from 1.3 to 15.6 inches, with SPI, parallel RGB, MIPI DSI, LVDS and eDP interfaces and optional capacitive or resistive touch. Round, square and portrait formats are included.
Who holds the quality certificates?
The group factory, Success Electronics Ltd, is certified to IATF 16949:2016, ISO 9001:2015 and ISO 14001:2015. The certificates are issued to the factory, not to the Hong Kong trading company.
Looking for a TFT LCD manufacturer for a new product? Send the window size, resolution, interface and touch needs. SuccessLCD will suggest the closest reference and what can be built around it, or browse the TFT LCD module catalogue first.
