How to Choose a Custom TFT Module with Optical Bonding and a PCAP Touch Screen for an Embedded Control Panel

To choose a custom TFT module with optical bonding and a PCAP touch screen for an embedded control panel, work from the front inwards: cover glass first, then the touch sensor and controller, then the bonding, and the TFT last. The cover sets the impact rating and the touch tuning. The bonding decides daylight contrast and whether a cracked front can be repaired. The TFT only has to suit the layout, the ambient light and the host processor. SuccessLCD supplies TFT modules with capacitive touch, starting from catalogue references such as the 3.5-inch S35001D (320 × 240, RGB) and the 10.1-inch S10MB1XH-07C0 (1024 × 600, LVDS).

Request a quote Touch panel and cover lens options

Air gap versus optically bonded PCAP touch display stackTwo cross-sections. In the air-gap stack the cover glass and PCAP sensor sit above an air gap, so light reflects at the front surface, at the underside of the sensor glass and at the top of the LCD polarizer, about 4 percent each. In the optically bonded stack a bonding layer fills the gap and only the front surface reflects. A worked example shows ambient contrast rising from about 3.4 to 1 to about 8 to 1.Air gap vs optically bonded PCAP touch displayRed lines: surfaces where glass or film meets air, each reflecting about 4 % of incoming lightAir gap: three reflecting surfacesCover glassPCAP sensor glassAir gapPolarizerLCD cellBacklight4 %4 %4 %Optically bonded: oneCover glassPCAP sensor glassBonding layerPolarizerLCD cellBacklight4 %Worked example: 850 cd/m² white, 0.85 cd/m² black, a 3,000 cd/m² background mirrored in the glassAir gap: 3 × 4 % = 12 % → 360 cd/m² reflected → ambient contrast about 3.4 : 1Bonded: 1 × 4 % = 4 % → 120 cd/m² reflected → ambient contrast about 8 : 1
Figure: an air-gap PCAP display has three glass-to-air surfaces in front of the LCD cell; a bonded one has one.

What is a PCAP touch screen, and what bonding changes

A PCAP (projected capacitive) touch screen senses a finger through the cover glass. A grid of transparent electrodes sits behind the glass, and the controller measures the capacitance change at each crossing, so it handles multi-touch and needs no pressure. An industrial PCAP touch screen behind 3 mm of glass, used with gloves, needs different tuning from a 0.7 mm lens; see gloves, water and thick glass.

Optical bonding fills the gap between the touch panel and the LCD with a clear adhesive whose refractive index, about 1.45 to 1.5, is close to glass. On a G+G sensor the cover and sensor are already laminated, so the decision is about the gap below the sensor. Bonding changes optics and mechanics: daylight readability, condensation, impact behaviour and repair. The sensor structures are compared in capacitive touch panel structures.

Cover glass: thickness and IK rating

  • Thickness. Thin glass is easier for the touch controller and weaker against impact. Our 3.5-inch S35001D uses a 0.70 mm chemically strengthened lens on a G+G sensor, which suits a handheld. A wall-mounted or public panel usually needs thicker glass.
  • Impact target. IEC 62262 grades impact by energy: IK08 is 5 J, a 1.7 kg hammer dropped from 0.30 m, and IK10 is 20 J, 5 kg from 0.40 m. One IK code on the enclosure drawing tells the glass supplier what to design for.
  • Edge support. Cover glass usually breaks from the edge, so the way the bezel and tape support it matters as much as thickness.
IK codeImpact energySame energy as a 0.5 kg steel ball dropped from
IK061 Jabout 0.20 m
IK072 Jabout 0.41 m
IK085 Jabout 1.0 m
IK0910 Jabout 2.0 m
IK1020 Jabout 4.1 m

Drop heights are for scale only (height = energy ÷ (mass × 9.81)); the rating comes from the IEC 62262 test.

Air gap or optical bonding: the contrast arithmetic

Each glass-to-air surface reflects about 4 % of the light that reaches it. An air-gap touch display has three in front of the LCD cell: the top of the cover, the underside of the sensor and the top of the polarizer. A bonded display has one. Indoors that hardly matters; near a window or outdoors, the reflections lift the black level and the image turns grey.

Worked example: ambient contrast with and without bonding. Take 850 cd/m² white, the typical luminance of S35001D, and assume a native contrast of 1,000:1, so black is 0.85 cd/m². The glass mirrors a 3,000 cd/m² background, such as a sunlit wall behind the operator.

  • Air gap: 3 × 4 % = 12 %, so 360 cd/m² is added to white and black. Contrast = (850 + 360) ÷ (0.85 + 360) ≈ 3.4:1.
  • Bonded: 1 × 4 % = 4 %, so 120 cd/m² is added. Contrast = (850 + 120) ÷ (0.85 + 120) ≈ 8.0:1.

Getting 8:1 with the air gap would take about 8 × 360.85 − 360 ≈ 2,530 cd/m² of white, three times the luminance, with the power and heat that go with it.

VIA optronics, a bonding specialist, quotes 5 to 10 times more contrast and about 8 % more perceived brightness from bonding, depending on the stack. Avnet notes that a bonded stack resists impact better and splinters less. With no cavity, there is also nowhere for condensation to form.

An air gap is still the right call for indoor panels under normal lighting, for products whose service plan swaps cracked covers, and for prototypes whose glass is still changing. Avnet describes it as the simplest and lowest-cost build.

Choosing the optical bonding material

OCA filmLiquid acrylic (LOCA)Silicone
FormAdhesive film, typically 50 to 250 µmDispensed liquid, cured by UVSoft gel or liquid that cures soft
Fits bestFlat, small and medium displaysLarge, curved or textured surfacesWide temperature ranges and outdoor use
Known risksSilvering (trapped air) on uneven surfacesBubbles in UV-shadowed areas; rework severely limited after full cure; yellowing under UV or heatProperties vary widely; ask for the specific grade’s data
StrengthsFast, clean process with little thermal stressHigh transmission, fills irregular gapsAbsorbs thermal and mechanical stress; virtually no yellowing under UV

Indoors, in the usual −20 to +70 °C range, any of the three can work; size, flatness and production rework decide. UV and temperature cycling outdoors or in vehicles favour silicone. The panel still sets the limits: S35001D is rated −20 to +70 °C operating and −30 to +80 °C storage, and no adhesive extends that.

Can an optically bonded touch display be repaired?

Usually you replace the bonded assembly. A cracked cover on a bonded stack means a new cover, sensor and LCD. Cured acrylic bonds are hard to separate, and Avnet notes that a bubble or particle found after liquid bonding means replacing the whole screen. An air gap lets service swap only the touch panel and cover.

If field replacement of the glass is in your service plan, put it in the RFQ: it changes the bonding material, the cover mounting and the spare-parts list. See also optical bonding vs air gap.

Host interface and catalogue references

A microcontroller with an RGB LCD peripheral needs a parallel RGB panel and enough RAM for the frame buffer. A Linux or Android processor usually offers MIPI DSI or LVDS for larger panels. The PCAP controller normally uses I²C plus interrupt and reset lines; keep that bus away from the backlight driver. Route ESD from the bezel to chassis ground rather than through the display FPC; the LCD ESD protection guide has the test levels.

ReferenceSize and resolutionDisplay interfaceTouchBody (reference)
S35001D3.5 in, 320 × 24024-bit RGB + SPI (ST7272A)G+G PCAP, FT5446-P03 over I²C, 10 points, 0.70 mm lens76.96 × 63.96 mm
S400MHZS-03F14 in, 480 × 480RGB + SPICapacitive83.7 × 83.7 mm
S400MB1ZS-01F24 in, 720 × 720MIPICapacitive84 × 84 mm
STFT50-02D5 in, 800 × 480RGBCapacitive, mirror cover glassConfirm with the drawing
S700MIWE-28C07 inConfirm with the datasheetCapacitive164.9 × 100 mm
S10MB1XH-07C010.1 in, 1024 × 600LVDSCapacitive235 × 143 mm
STFT1010D10.1 in, 800 × 1280MIPICapacitiveConfirm with the drawing

Cover size and printing, bonding and touch tuning are project options on these references; see touch panels and cover lenses. S35001D’s touch panel passes at least 85 % of the light, so set the backlight level with the touch stack included.

What to send for a quote

ItemWhat it decides
Cover outline, thickness, printing and windowsThe lens drawing and the bezel
Impact target (IK code) and front sealingGlass thickness, edge support, gasket or adhesive
Gloves, water, cleaning agentsSensor pattern and controller tuning
Ambient light: indoor, near a window, outdoorAir gap or bonding, brightness, surface treatment
Operating and storage temperatureBonding material and panel choice
Host processor and its display outputsInterface and touch bus
Service plan: replace the glass or swap the unitBonding material and cover mounting
Yearly volume and product lifeSupply planning; see component obsolescence

PCAP touch and optical bonding FAQs

How do I choose a custom TFT module with optical bonding and PCAP touch for an embedded control panel?

Start with the cover glass: size, thickness, strengthening, printing and IK target. Then choose the PCAP sensor and controller that read through it with gloves and water, and decide between an air gap and bonding from the ambient light, temperature range and repair plan. Pick the TFT size, brightness and interface last, to suit the host processor.

What is a PCAP touch screen?

A projected capacitive touch screen. Transparent electrodes behind the cover glass let a controller detect the capacitance change a finger causes at each grid crossing. It supports multi-touch, needs no pressure and works through glass.

Can an optically bonded touch display be repaired?

Usually not at component level. A cracked cover on a bonded stack normally means replacing the cover, sensor and LCD together. An air-gap design lets service replace only the touch panel and cover, so say in the RFQ if field repair matters.

Is optical bonding worth it for an indoor control panel?

Often not. Indoors, the extra reflections of an air gap cost little contrast, and an air gap is simpler to build and service. Bonding pays off near windows, under strong lighting, outdoors, where condensation forms, or where the front must survive impacts.

Building a control panel front? Send the cover drawing, IK and sealing targets, the lighting, the temperature range, your host processor and how you will service a cracked cover. We will suggest a catalogue reference and the cover and bonding options that fit. See our custom LCD solutions, or ask about a bonded PCAP display.

Scroll to Top
Get a QuoteWhatsApp