Waterproof Touch Screen Displays: How to Seal an OEM Front to IP65

A waterproof touch screen for OEM equipment is a capacitive TFT module behind a cover glass that seals the front of the housing, with the touch controller set up so water is not read as a finger; SuccessLCD supplies the display and touch stack, starting from catalogue references such as the S35001D (3.5-inch, 320 × 240, G+G capacitive touch, 0.70 mm chemically strengthened lens) and the S10MB1XH-07C0 (10.1-inch, 1024 × 600, LVDS, capacitive touch). The module itself has no IP rating. IP65 or IP67 belongs to the finished product: it comes from the joint between the glass and the housing, and it is confirmed by testing to IEC 60529.

Request a quote Touch panel and cover lens options

Two ways to seal a touch display frontCross-sections. A: the cover glass sits on the outside of the housing and is bonded to the housing face with adhesive tape under its printed border; the PCAP sensor and TFT module sit behind the glass inside the opening. B: a bezel in front presses a gasket onto the printed border of the glass. Both have a vent in the back wall. In both, the seal touches only the printed border, not the touch active area.A · Glass bonded to the housing faceTFT modulecover glass = product frontadhesive tape sealPCAP sensorprinted borderventB · Glass behind a bezel and gasketTFT modulebezelgasket, pressed evenlyPCAP sensorprinted borderventIn both: the seal sits on the printed border, never on the touch active area.The IP rating belongs to the finished product and is confirmed by test.
Figure: the cover glass either sits on the housing face on an adhesive seal (A) or behind a bezel that presses a gasket onto its printed border (B). A vent in the back wall equalises pressure.

What waterproof means: IP65, IP66, IP67 and IP69K

“Waterproof” is not a test. Buyers and test labs use the IP code from IEC 60529: the first digit covers dust, the second sets the water test.

CodeWater testTypical use
IP65Dust-tight; water jets from a 6.3 mm nozzle, 12.5 L/min at about 3 m, at least 3 minutesEquipment outdoors in rain, or hosed down
IP66Dust-tight; powerful jets from a 12.5 mm nozzle, 100 L/min at about 3 m, at least 3 minutesExposed decks, vehicles, heavy washdown
IP67Dust-tight; temporary immersion with the lowest point 1 m below the surface for 30 minutesHandheld units that can be dropped in water
IP69KISO 20653: 80 °C water at 80 to 100 bar, 14 to 16 L/min, nozzle 10 to 15 cm from the productFood plants and vehicles cleaned with hot pressure washers

An immersion rating does not cover jets, so a product that must survive both carries both codes, for example IP65/IP67. Pick the code from how the product is cleaned and mounted, then design the front for that test.

Two ways to seal an IP65 touch screen front

The seal is one joint, between the cover glass and the housing, and it is built in one of two ways.

  • Glass bonded to the housing face. The cover glass is larger than the opening and sits on the outside of the housing, held by an adhesive tape or a dispensed adhesive under its printed border. The front is flush and easy to wipe. Avnet notes that tape is faster to assemble, while a liquid adhesive also fills the gap between glass and frame and seals better against humidity, but it cures more slowly. Replacing the glass means breaking the bond.
  • Glass behind a bezel and gasket. A bezel presses an elastomer gasket onto the glass border. Elo recommends silicone, polyurethane or cross-linked saturated polyolefin for a watertight gasket, compressed evenly around the whole perimeter. The bezel leaves a step at the edge, but the glass can be removed for service.

Three rules apply to both, all from Elo’s PCAP integration guidelines. The seal touches only the printed, inactive border of the glass: tape or rubber on the active area changes the capacitance there and can cause false touches. Sealing materials must be non-conductive. Sulfur-cured rubber should not be used, because sulfur can attack the silver electrode pattern in the sensor.

Size the cover glass for the seal

A standard module lens is cut close to the module size, so it cannot reach a housing seal. On the S35001D the cover glass is 76.60 × 63.60 mm and the module outline is 76.96 × 63.96 mm, so the glass ends inside the module edge. A sealed front needs a larger cover glass, made for the project, and the touch is tuned again for it.

Worked example: cover glass for a sealed 3.5-inch front. Take the S35001D drawing values: module outline 76.96 × 63.96 mm, viewing area 70.68 × 53.16 mm. Assume the housing opening clears the module by 1.0 mm on each side and the adhesive needs a 5.0 mm land all round (take the real minimum from the tape or adhesive maker). The opening is 76.96 + 2 × 1.0 = 78.96 mm by 65.96 mm. The glass is 78.96 + 2 × 5.0 ≈ 89.0 mm by 65.96 + 2 × 5.0 ≈ 76.0 mm. With the viewing area centred, the printed border is (89.0 − 70.68) ÷ 2 ≈ 9.2 mm wide at the sides and (76.0 − 53.16) ÷ 2 ≈ 11.4 mm at the top and bottom. The viewing area is not always centred on the module, so take the offsets from the drawing.

Glass thickness is set by impact as much as by water; the PCAP control panel guide lists IK impact energies. For printing and coatings, see touch panels and cover lenses and what can be customized on a TFT module.

Touch on wet glass

A sealed front keeps water out of the housing, but water on the glass can still be read as a touch. Most PCAP controllers scan in mutual-capacitance mode, which gives clean multi-touch but responds to droplets and water films. Self-capacitance mode is much less affected by water, but it cannot separate several fingers as well. Wet-touch designs combine the two and add firmware that recognises water patterns; Elo’s patents on water-immune PCAP describe this trade.

Specify the water you expect: rain drops, a running film from a hose, salt spray or cleaning agents. Then test with that water on the final cover glass, with the product grounded as it will be installed. Droplets and running water behave differently, and a tuning that ignores one may not ignore the other. Gloves pull the other way, since they need more sensitivity; see capacitive touch with gloves, water and thick glass.

Rain on a hot enclosure: why sealed fronts still leak

When a hot enclosure is cooled quickly, for example by a shower on a sunny day, the air inside contracts and pulls a vacuum. Gore, which makes membrane vents for this problem, notes that repeated pressure swings stress housing seals until they fail and then draw water in. Air sealed at 50 °C (323 K) and cooled to 20 °C (293 K) in a rigid box drops to 101.3 × 293 ÷ 323 ≈ 91.9 kPa. That is about 9.4 kPa below the outside, the pressure under roughly 0.96 m of water: close to the IP67 immersion depth, applied to the front seal every time it rains. A membrane vent in the back of the housing equalises the pressure and keeps liquid water out.

Condensation is the other risk. An air gap between the cover glass and the TFT is a cavity where moisture can condense and fog the image. Optical bonding fills that gap with a clear adhesive, so no cavity is left; see optical bonding vs air gap.

Catalogue references for a sealed touch front

SuccessLCD lists these capacitive touch modules as starting points. None is sold as a waterproof unit: the cover glass, its printed border and the touch tuning are set for each project.

ReferenceSize and resolutionDisplay interfaceTouchBody (reference)
S35001D3.5 in, 320 × 24024-bit RGB + SPI (ST7272A)G+G PCAP, FT5446-P03 over I²C, 0.70 mm lens76.96 × 63.96 mm
S500MI4WS2-03F15 inConfirm with the datasheetCapacitive touch display assembly120.7 × 80.44 mm
S700MIWE-28C07 inConfirm with the datasheetCapacitive touch display assembly164.9 × 100 mm
S10MB1XH-07C010.1 in, 1024 × 600LVDSCapacitive235 × 143 mm

S35001D is rated −20 to +70 °C operating, with 850 cd/m² typical luminance and an anti-glare top polarizer. For the other references, brightness and temperature range come from the datasheet of the revision you are quoted. For products used in direct sun, read sunlight readable displays before choosing the panel.

What to send for a waterproof touch screen

ItemWhat it decides
IP code and test standard (IP65, IP66, IP67, IP69K)Seal design, glass mounting and vent
Water type: rain, hose, salt spray, cleaning agents, hot washdownTouch tuning, seal and coating materials
Gloves or bare fingersTouch sensitivity and glass thickness
Front design: glass bonded to the housing or behind a bezelGlass outline, printed border and seal land
Impact target (IK code)Glass thickness and edge support
Operating temperature and sun exposurePanel, brightness and bonding
Host processor and its display interfaceChoice of reference
Yearly volume and product lifeSupply planning

Waterproof touch screen FAQs

Is a capacitive touch screen waterproof?

Not on its own: a touch display module has no IP rating. The product becomes waterproof when the cover glass is sealed to the housing, the touch is tuned to ignore water and the finished unit passes the IEC 60529 test for its IP code.

Can a touch screen work when it is wet?

A projected capacitive screen can, if the controller is set up for water: wet-touch designs add self-capacitance measurements and water detection to mutual-capacitance scanning. Test with the water your product will see, on the final cover glass.

What IP rating does an outdoor touch screen need?

IP65, rain and water jets from any direction, is the usual target for outdoor equipment. Choose IP66 for powerful jets, IP67 if the unit can be immersed and IP69K for hot pressure washdown, and mark both codes, such as IP65/IP67, if it must pass jets and immersion.

Can SuccessLCD supply the cover glass for our sealed housing?

Yes. The cover glass outline, thickness, printed border and coatings are set per project, and the touch is tuned for the final glass. The seal, bezel and vent belong to your housing, and the IP test is done on your finished product.

Designing a sealed touch front? Send the IP code, how the product is cleaned, the front design, glove use, temperature range and host processor. SuccessLCD will suggest a catalogue reference and the cover glass and touch setup that fit. Browse the TFT LCD module catalogue, or ask about a waterproof touch screen.

Scroll to Top
Get a QuoteWhatsApp