Anti-Glare vs Anti-Reflective Cover Glass for Displays: AG, AR and AF Compared

Anti glare vs anti reflective comes down to one difference: an anti-glare (AG) surface scatters the reflection, and an anti-reflective (AR) coating removes most of it. AG turns a sharp mirror image into a soft haze without lowering the total reflected light, while a multilayer AR coating cuts each glass surface from about 4 percent to under 1 percent and keeps the image sharp. For a display read in sunlight, AR does more for contrast. For bright indoor lighting AG may be enough, and the two can be combined, usually with an anti-fingerprint (AF) layer on top.

Request a quote Touch panel and cover lens options

How plain, anti-glare and anti-reflective glass treat a reflectionThree panels. Plain glass reflects about 4 percent of the incoming light as a sharp mirror image. Anti-glare glass has a rough surface that scatters about the same amount of light in many directions, giving a soft haze. Anti-reflective glass has thin interference layers on the surface, so under 1 percent is reflected and most light passes through, keeping the image sharp.Plain, anti-glare and anti-reflective glass: what happens to a reflectionPlain glasscover glassabout 4 % reflectedas a sharp mirror imageAnti-glare (AG)cover glassabout the same lightscattered into a soft hazeAnti-reflective (AR)cover glassAR layersunder 1 % reflectedimage stays sharpPer air-glass surface at normal incidence, glass index about 1.5. An AF layer on top changes cleaning, not reflection.
Figure: AG spreads the reflection, AR removes most of it. The two treatments solve different problems and can be combined.

Where the reflection comes from: about 4 percent per surface

Light reflects wherever the refractive index changes. At normal incidence the reflected fraction is R = ((n − 1) ÷ (n + 1))², which for glass at n ≈ 1.5 in air is 0.04, or 4 percent. A cover lens mounted over an air gap puts three such surfaces in front of the pixels: the front of the cover, the back of the cover and the front of the LCD.

Worked example: contrast at 10,000 lux. Assume a display with 500 cd/m² white and 0.5 cd/m² black, in 10,000 lux of daylight, and count only the glass surfaces. Reflected luminance is illuminance × reflectance ÷ π. With three untreated surfaces, about 12 percent: 10,000 × 0.12 ÷ π ≈ 382 cd/m². Contrast becomes (500 + 382) ÷ (0.5 + 382) ≈ 2.3 to 1. With an AR front surface at 0.5 percent and the two inner surfaces removed by optical bonding: 10,000 × 0.005 ÷ π ≈ 16 cd/m², and contrast is (500 + 16) ÷ (0.5 + 16) ≈ 31 to 1. Reflections inside the LCD itself are ignored here, so real figures are lower, but the ranking holds.

Anti-glare glass: scatter the reflection

AG glass has a micro-rough surface, made by chemical etching or by depositing a textured coating. The roughness breaks a mirror-like reflection into a diffuse one. The total reflected light is not reduced. It is spread out, so a window or lamp behind the user stops showing as a sharp image.

AG is specified mainly by gloss. Abrisa, for example, lists standard gloss levels of 40, 60, 90 and 120 for its etched glass, in thicknesses from 1.1 to 6.0 mm. A lower gloss number is more matte.

The cost is image quality. The texture softens fine detail, and on high-resolution panels it can cause sparkle, a grainy look that Corning describes as a side effect of glare reduction. One display maker advises a finer texture above about 300 PPI. A textured surface also holds contamination more readily than a smooth one.

Anti-reflective coating: cancel the reflection

An AR coating is a stack of thin transparent layers whose thicknesses are chosen so that light reflected from each boundary cancels by interference. A single quarter-wave layer of magnesium fluoride brings a glass surface from 4 percent to about 1 percent. Broadband multilayer coatings for 400 to 700 nm commonly stay below 0.5 percent. The surface stays smooth, so sharpness and colour are unchanged.

A catalogue specification shows how this is written down. Präzisions Glas & Optik lists an average residual reflection of 1 percent or less per side from 440 to 670 nm, with both sides coated.

The weak points are fingerprints and wear. Skin oil on an AR surface changes the interference locally and shows clearly, which is why AR on a touch surface is commonly finished with an oil-repellent layer. AR layers are also thin, so ask how the coating is protected against abrasion.

Anti-fingerprint coating: keep the surface clean

An AF coating is an oleophobic top layer on the user side. It does not change reflection. It makes oil and water bead up so marks are less visible and wipe off easily. The usual measure is the water contact angle. The same supplier quotes more than 110 degrees for its oleophobic layer. The layer wears with use, so the figure that matters is the contact angle after a stated abrasion test, not only the value when new.

Anti glare vs anti reflective coating: side by side

Anti-glare (AG)Anti-reflective (AR)Anti-fingerprint (AF)
What it doesScatters the reflectionReduces the reflectionRepels oil and water
HowEtched or coated micro-roughnessThin-film interference layersOleophobic top layer
Reflected lightAbout the same, spread outFrom about 4 percent to under 1 percent per surfaceUnchanged
Image sharpnessSofter, with a risk of sparkleUnchangedUnchanged
Main riskSparkle on fine pixel pitchFingerprints, abrasionWears with use
Specified byGloss level, haze, processAverage reflectance per side over a wavelength bandWater contact angle, new and after abrasion

Surface treatment and optical bonding

AG and AR act on the outer surface only. The two inner surfaces of an air-gap stack are removed by optical bonding, as the worked example shows. For a sunlight-readable product, bonding and a front AR coating do the most. Add AG when mirror-like reflections still bother users. See optical bonding vs air gap and sunlight-readable TFT displays.

Our catalogue has capacitive touch references with a cover outline of 164.4 × 99.5 mm (S700GG-42, 7-inch class) and 247 × 152 mm (S10GF2-94, 10-inch class). The surface treatment is confirmed for each project, along with the other cover lens options.

What to write on the cover lens drawing

  • Which side carries each treatment. AF goes on the user side only.
  • AG: process (etched or coated), gloss level and haze, with tolerances.
  • AR: average reflectance per side over a stated band, for example 1 percent or less from 440 to 670 nm.
  • AF: water contact angle when new and after a stated number of abrasion cycles.
  • A sparkle check on the real display at its pixel pitch, agreed on an approval sample.

When not to use each one

Do not rely on AG alone outdoors. It removes the mirror image but leaves the haze that lowers contrast. Avoid a coarse AG on small text at close viewing distance. Do not put AR on a touch surface without AF. And do not treat AF as permanent: on a product cleaned many times a day, set the abrasion requirement to match.

FAQ

What is the difference between anti-glare and anti-reflective?

Anti-glare roughens the surface so reflections scatter into a soft haze, and the total reflected light stays about the same. Anti-reflective uses thin-film interference to cut the reflection itself, from about 4 percent per glass surface to under 1 percent. AG trades some sharpness, and AR keeps the image clear.

Is anti-glare or anti-reflective better in sunlight?

Anti-reflective, because sunlight readability depends on how much light the screen reflects, and only AR lowers that amount. Combine it with optical bonding to remove the internal air-glass surfaces as well. AG alone removes the mirror image but leaves the haze.

Can a cover glass have both anti-glare and anti-reflective treatment?

Yes. The glass can be etched for anti-glare, coated for anti-reflection and finished with an anti-fingerprint layer on the user side. Check sparkle on the real display, because the AG texture interacts with the pixel pitch.

Does an anti-fingerprint coating wear off?

It wears with abrasion, like any thin surface layer. Specify the water contact angle when new and the value it must keep after a stated number of abrasion cycles. More than 110 degrees is a published figure for one new oleophobic coating.

Specifying a cover lens? Send the display size and resolution, the lighting where it is used, how it is cleaned and whether it is bonded. We will propose a surface treatment and the acceptance values for the drawing. See touch and cover lens options and custom TFT displays, or ask about cover glass treatment.

Scroll to Top
Get a QuoteWhatsApp